TRIGGERTECH T Series Diamond Trigger User Guide

TRIGGERTECH T Series Diamond Trigger

ÜZERİNDEVIEW

These instructions cover safe installation, pre-use trigger safety/function checks, and adjustable pull-weight setup for TriggerTech Tikka triggers. Read all disclaimer and warranty terms before proceeding.

Özellikler

TriggerTech Memnuniyet Garantisi
TriggerTech triggers have distinctively less creep than competitors’ products. While most shooters view this as a benefit, some may not enjoy the distinct, crisp feeling of a TriggerTech trigger. If you are the original purchaser and are not satisfied with the zero-creep break of your TriggerTech trigger, you may return it to TriggerTech within thirty (30) days of purchase, in the original packaging and with proof of purchase. Provided the trigger is undamaged, TriggerTech will refund the purchase price.

TriggerTech Tikka triggerKULLANIM TALİMATI

Adım 1: Unload your firearm and remove the bolt and stock

• a) Kurulum ve kullanım öncesinde TriggerTech Yasal Uyarısını ve TriggerTech Ömür Boyu Garantisini okuyun.
• b) Remove all ammunition and magazines.
• c) Remove the bolt from your firearm by pressing the bolt release while sliding the bolt aft-ward.
• d) Using the appropriate Torx driver (typically T25), carefully remove your stock from the action.

NOT: Remember the size and location of each bolt you remove from the stock for reassembly.

Adım 2: Remove the existing trigger

Unscrew the trigger bolt with the appropriate screwdriver (typically a Hex 5) to remove the trigger (trigger safety on).

Adım 3: Install your TriggerTech trigger

Insert the TriggerTech trigger assembly into the action with the trigger safety on. Using the same factory trigger bolt from Step 2. Tighten bolt to 55-65 in-lbs.

Adım 4: Re-install the stock and bolt

• a) Using the same screws from Step 1, re-install your stock onto the action.
• b) Insert the bolt and check the bolt release functionality. The bolt should only be removable while the bolt release is being pressed. When the bolt release is not being pressed, the bolt should not be removable.

Adım 5: Check trigger safety and function

Prior to using your firearm, perform the following tests without ammunition to see if your installation was done correctly.

• a) Place the Safety in the SAFE position and verify that the bolt handle is locked and cannot be lifted.
• b) Place the Safety in the FIRE position and cycle the bolt. The firing pin should remain cocked and should not release
• c) Place the Safety in the FIRE position and cycle the bolt to cock the firing pin. Then place the Safety in the SAFE position and pull the trigger lever. The firing pin should NOT release or move.
• d) Place the Safety in the FIRE position, cycle the bolt, and pull the trigger lever. The firing pin should release
• e) Place the Safety in the FIRE position and cycle the action. Then place the Safety in the SAFE position and move the safety back to the FIRE position. The firing pin should NOT release or move.
• f) Place the Safety in the SAFE position and apply firm pressure to the trigger lever (no audible clicks should be heard). Release the trigger lever, then move the Safety to the FIRE position. The firing pin should not release.
• g) Place the Safety in the FIRE position, cycle the bolt to cock the firing pin, and firmly tap the buttstock against a padded surface. The firing pin should not release (NEVER PERFORM THIS STEP WITH LIVE AMMUNITION).
• h) At a properly supervised shooting range, safely repeat Steps 5b through 5f using live ammunition with the rifle pointed in a safe direction to confirm correct trigger operation. DO NOT PERFORM STEP 5g WITH LIVE AMMUNITION.

Adım 6: Pull weight adjustmentYour TriggerTech trigger is set near the middle of the advertised pull weight range and can be adjusted in increments. To adjust pull weight, insert the supplied 5/64” Allen wrench into the set screw located at the bottom of your trigger. To increase pull weight, rotate the set screw clockwise. Pull weight varies between actions.

UYARI: Tetiğinizi fabrika ayarında veya üzerinde çalıştırmanız önerilir. Çekme ağırlığınızı ayarlarken dikkatli olun ve canlı mühimmat kullanmadan önce 5. Adımı tekrarlayın.

NOT: Always keep the set screw engaged with at least three “Clicks” to prevent the set screw from falling out.

Çekme ağırlığı ayar uyarısı

The TriggerTech Tikka trigger has an adjustable pull weight. The factory setting is near the middle of the advertised range (caution – pull weights may vary dramatically from the factory setting due to variability found in actions). There is such a thing as a trigger that is too light to be considered safe. This weight will change depending on the specifics of the gun, the experience of the shooter, and the intended use case (how the gun and all of its components are operated/handled).

TriggerTech strongly recommends that you get some trigger time on your TriggerTech trigger before adjusting the break weight below the factory setting (a trigger set at 4.0 lbs is safer than a trigger set at 2.5 lbs). As you reduce the pull weight of a TriggerTech trigger, you are reducing the amount of spring tension in the trigger, and it is possible that you may reach a point where the trigger in a specific gun is not safe for the intended use case and/or the shooter.

Your trigger’s pull weight may change slightly over the trigger’s lifetime as the parts wear in. Any change should be gradual and not in excess of 6 oz or 15% (whichever is less). A change in excess of this range, or any sudden change, is a sign that something is not right, and your firearm may not be safe. Stop using your trigger and contact TriggerTech Support (support@triggertech.com) at 1-888-795-1485. TriggerTech recommends that you check your pull weight prior to use to ensure it is set at an appropriate level.

See TriggerTech Bolt Action Pull Weight Guide. To ensure safety, never chamber a round until the rifle is safely pointed at a target and you are ready to fire. Shooters are reminded to always follow the NRA Gun Safety Rules.

Pull weight adjustment warning (continued)

Bakım / Temizlik

Your TriggerTech trigger is designed to operate maintenance- and lubricant-free. It is recommended that you minimize the amount of oil and gun cleaning products that get in contact with the trigger.
Tetiğinizin kirlenme nedeniyle düzgün çalışmadığını düşünüyorsanız, aşağıdaki adımları izlemenizi öneririz:

1. Ateşli silahınızın boş olduğundan emin olun.
2. Cycle the action and dry fire the rifle repeatedly. If necessary, try holding the rifle in different orientations while doing this.
3. If step 2 is unsuccessful, remove your TriggerTech trigger from the action, and you can try to clean with compressed air and/or a grease-cutting agent that does not leave residue. We recommend lighter fluid, letting it dry, and blowing out the trigger with compressed air. Follow the TriggerTech Installation Instructions when reinstalling your trigger.
4. 3. adım başarısız olursa, tetik yuvanızı açmanızı ÖNERMİYORUZ ve TriggerTech ile iletişime geçerek tetiğinizin bakımını yaptırmanızı öneririz. Not: "Çıkarıldığında geçersiz" seçeneğinin kırılması, tetiğinizi açtığınız anlamına gelir ve Sınırlı Garanti'yi geçersiz kılabilir.

In the event you decide to ignore our recommendations and open your TriggerTech trigger, this is an image of the internal assembly:

Setup & Use Quick Guide

1. boşaltmak the firearm and remove all ammunition and magazines.
2. Remove the bolt (press the bolt release while sliding the bolt aft-ward).
3. Remove the stock from the action using the appropriate Torx driver (typically T25). Note the size and location of each bolt for reassembly.
4. Remove the existing trigger: Unscrew the trigger bolt (typically Altıgen 5) and remove the trigger (with trigger safety on).
5. Install the TriggerTech trigger: Insert the TriggerTech trigger assembly into the action with the trigger safety on. Use the same factory trigger bolt and tighten to 55–65 in-lbs.
6. Reinstall stock and bolt: Re-install the stock using the same screws. Insert the bolt and verify bolt-release functionality: the bolt should be removable only while the bolt release is being pressed.
7. Pre-use safety/function tests (no ammunition): Verify safety lock behavior, firing-pin behavior in FIRE vs SAFE positions, and that the firing pin does/does not release according to the listed test steps.
8. Adjust pull weight (if needed): Sağlanan 5/64 Allen wrench into the set screw at the bottom of the trigger. Rotate clockwise to arttırmak pull weight. Keep the set screw engaged with at least three clicks to prevent it from falling out. Repeat the safety/function tests in Step 5 prior to using live ammunition.

Damaging your trigger

We have gone to great lengths to design the most reliable and dependable triggers on the market and we are constantly striving to improve the safety and performance of all TriggerTech products. However, TriggerTech triggers are precision mechanical devices, and they can be damaged. A damaged trigger could be or become unsafe.
The following are conditions that may damage your trigger:

• Pierced Primer / Overpressure – the dynamic forces of the event may damage your trigger and prevent it from functioning safely.
• Untimed Action Damage – when you close the bolt with an untimed action, you are hammering your trigger sear with the cocking piece. This can cause accelerated and unusual wear on your trigger and cocking piece. Excessive wear caused by an untimed action may cause your firearm to become unsafe as you can damage and /or break the cocking piece and/or trigger components. This is especially true with aggressive or repetitive dry cycling of your action. Cycling an untimed action without ammunition is more severe from a wear perspective than cycling with ammunition, as moving ammunition will slow the bolt. TriggerTech recommends that you ensure your action is properly timed prior to use.
• Damaging your trigger when installing trigger pins during install – if you do not follow Step 4, you may damage the trigger by attempting to hammer a trigger pin through a trigger pin hole that is not aligned with the action mounting hole. Damage severity can range from cosmetic damage to the housing to catastrophic

Damaging your trigger (continued)

damage where the trigger will no longer be able to be mounted to the action or function safely. It is possible to cause the trigger to fall out of factory alignment and in this case may cause degradation of the trigger’s safety and/or performance.
Shooters are reminded:

• Your trigger’s pull weight should not change suddenly. A sudden change in pull weight is a sign that something is not right, and your firearm may not be safe. Stop using your trigger and contact TriggerTech Support (support@triggertech.com) at 1-888-795-1485.
• Your trigger’s pull weight may change slightly over the trigger’s lifetime as the parts wear in. Any change should be gradual and not in excess of 6oz or 15% (whichever is less). A change in excess of this is a sign that something is not right, and your firearm may not be safe. Stop using your trigger and contact TriggerTech Support (support@triggertech.com) 1-888-795-1485.
• If you notice a change in your trigger’s ability to hold the firing pin when closing the bolt, do not try to overcome this by increasing pull weight. Stop using the trigger immediately and contact TriggerTech Support (support@triggertech.com) at 1-888-795-1485.
• Always safety check your equipment prior to use and when using live ammunition.
• Always follow the NRA Gun Safety Rules. (https://gunsafetyrules.nra.org)

Sorun giderme

• Bolt-release / safety not correct: If, with the safety in the SAFE position, the bolt handle is not locked or can be lifted, stop and re-check installation before use.
• Firing pin releases when it should not (no ammunition): During Step 5 tests, if the firing pin releases when the safety is SAFE, or does not behave as specified when cycling the bolt in FIRE vs SAFE, stop using the firearm and review the installation and safety/function checks.
• Firing pin releases during the “firm pressure” test: In Step 5f, apply firm pressure to the trigger lever in SAFE—there should be no audible clicks. If the firing pin releases after moving to FIRE, stop and correct the issue before any live-ammunition testing.
• Grip/impact test failed (no live ammunition): Step 5g requires tapping the buttstock only without live ammunition. If the firing pin releases, do not proceed to live ammunition; stop and contact TriggerTech Support.
• Pull-weight change exceeds guidance: If pull weight changes suddenly or exceeds 6 ons or %15 (whichever is less), stop using the trigger and contact TriggerTech Support.