ANCEL DS500 Elite OBD2 Scanner and BT310 Battery Tester User Manual

1. Giriş

This manual provides detailed instructions for the ANCEL DS500 Elite Bidirectional Scan Tool and the ANCEL BT310 12V/24V Car Battery Tester. Please read this manual thoroughly before operating the devices to ensure correct usage and optimal performance. Keep this manual for future reference.

2. Ürün Bittiview

2.1 ANCEL DS500 Elite Bidirectional Scan Tool

The ANCEL DS500 Elite is an advanced diagnostic scan tool designed for comprehensive vehicle system analysis. It features bidirectional control capabilities, allowing users to send commands to vehicle modules and monitor system responses. This tool supports full-system deep scans and offers over 3,000 active test commands.

• Çift Yönlü Kontrol: Perform active tests on various components like fuel pumps, cooling fans, windows, and mirrors.
• Full System Deep Scan: Uncover critical data from every module and sensor, including Engine, ABS, Airbag, Transmission, TPMS, SAS, ESP, BCM, HVAC, EBS, and ACM.
• Hot Reset Service: Access over 28 maintenance reset functions for various car brands, including D-P-F Regeneration, AdBlue Reset, Oil Life Reset, EGR Adaptation, IMMO Reset, Gear Learning, Battery Matching, SAS Calibration, A/F Ratio/Fuel Reset, ABS Bleeding, Air Suspension Reset, NOx Sensor Reset, AFS Reset, ETA Reset, Coolant Pump Activation, Brake-pad Reset, Seat Calibration, and Airbag Reset.
• Ömür Boyu Ücretsiz Güncellemeler: Ensures compatibility with evolving vehicle diagnostic systems without subscription fees.

2.2 ANCEL BT310 12V/24V Car Battery Tester

The ANCEL BT310 is a versatile battery load tester compatible with both 12V and 24V battery systems. It supports various battery types and provides accurate health assessments, cranking tests, and charging tests.

• Evrensel Uyumluluk: Supports 12V and 24V Lithium and Lead-Acid batteries, including Flooded, AGM (Spiral & Flat Plate), GEL, and EFB types.
• Çoklu Standartlar: Compatible with major battery standards such as CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, and GB.
• Key Diagnostics: Measures State of Charge (SOC), State of Health (SOH), Voltage Test, Rated and Measured CCA, and Internal Resistance.
• Test Sonuçları: Provides clear results: [GOOD BATTERY], [GOOD-RECHARGE], [CHARGE & RETEST], [REPLACE BATTERY], and [BAD CELL-REPLACE].

3. Kurulum

3.1 ANCEL DS500 Elite Setup

1. Güç Açık: Connect the DS500 Elite to the vehicle's OBD-II port. The device will power on automatically.
2. Başlangıç ​​konfigürasyonu: Follow the on-screen prompts to select language, time zone, and Wi-Fi connection.
3. Yazılım Güncellemeleri: Ensure the device is connected to Wi-Fi and check for available software updates to maintain optimal performance and vehicle compatibility.

3.2 ANCEL BT310 Setup

1. Aküye Bağlan: Ensure the vehicle engine is off. Connect the red clamp pilin pozitif (+) terminaline ve siyah clamp negatif (-) terminale.
2. Güç Açık: BT310, bataryaya bağlandıktan sonra otomatik olarak açılacaktır.
3. Pil Tipini Seçin: Use the navigation buttons to select the correct battery type (e.g., Flooded, AGM, GEL, EFB, Lithium) and standard (e.g., CCA, BCI) as prompted on the screen.

4. Kullanım Talimatları

4.1 ANCEL DS500 Elite Operation

1. Araç Bağlantısı: Plug the OBD-II cable into the vehicle's diagnostic port, usually located under the dashboard.
2. Araç Tanımlaması: The DS500 Elite will automatically detect the vehicle's VIN or prompt you to manually enter vehicle information (make, model, year).
3. Diagnostic Menu: Navigate the main menu to select desired functions:
   • Teşhis: Perform full system scans, read/clear fault codes, view live data streams, and check I/M readiness.
   • Aktif Test: Select specific control modules and components to perform bidirectional tests (e.g., activate ABS pump, cycle cooling fan).
   • Hizmet: Access various reset and maintenance functions (e.g., Oil Reset, EPB Reset, SAS Calibration).
   • Güncelleme: Check for and install software updates.
4. Veri Yenidenview: After performing tests, review the diagnostic reports, freeze frame data, and live data graphs on the device screen.

4.2 ANCEL BT310 Operation

1. Ana Menü: Once powered on, the BT310 will display the main menu with options like 'Battery Test', 'Cranking Test', 'Charging Test', and 'Review Data'.
2. Pil Testi: Select 'Battery Test'. The device will prompt you to enter the battery's rated CCA (Cold Cranking Amps) or other standard values. Follow the on-screen instructions. The test will provide results such as SOC, SOH, Voltage, Measured CCA, and Internal Resistance, along with a clear status (e.g., GOOD BATTERY, REPLACE BATTERY).
3. Marş Testi: Select 'Cranking Test'. The device will instruct you to start the vehicle. It will then measure the cranking voltage and time, providing an assessment of the starter system's performance.
4. Şarj Testi: Select 'Charging Test'. The device will instruct you to run the engine at idle and then at a higher RPM (e.g., 2500 RPM). It will measure the alternator's output voltage and ripple, assessing the charging system's efficiency.
5. Review Veri: 'Yeniden' seçeneğini seçin.view Data' to view Daha önce kaydedilen test sonuçları.

5. Bakım

• Temizlik: Use a soft, dry cloth to clean the device screens and bodies. Avoid using abrasive cleaners or solvents.
• Depolamak: Her iki cihazı da kuru, serin bir ortamda, doğrudan güneş ışığından ve aşırı sıcaklıklardan uzakta saklayın.
• Kablo Bakımı: Inspect cables regularly for any signs of damage. Do not pull on the cables to disconnect them; always grasp the connector.
• Software Updates (DS500 Elite): Regularly check for and install software updates to ensure the scanner has the latest vehicle data and diagnostic capabilities.

6. Sorun Giderme

• Cihaz Açılmıyor:
  • DS500 Elite: Ensure the OBD-II cable is securely connected to the vehicle's diagnostic port. Check the vehicle's battery for sufficient charge.
  • BT310: cl olduğunu doğrulayınamps are correctly connected to the battery terminals (red to positive, black to negative) and that the battery has sufficient voltage.
• Communication Error (DS500 Elite):
  • Aracın kontak anahtarının açık olup olmadığını kontrol edin.
  • Ensure the OBD-II connector is fully seated.
  • Verify that the vehicle supports the OBD-II protocol.
  • Try testing on a different compatible vehicle to rule out a vehicle-specific issue.
• Hatalı Pil Test Sonuçları (BT310):
  • Pilin cl olduğundan emin olunamps are clean and have good contact with the battery terminals.
  • Verify that the correct battery type and CCA rating were entered into the tester.
  • Ensure the battery is fully charged before testing for the most accurate results.
• Screen Freezes or Device Unresponsive:
  • Perform a soft reset by holding the power button (if available) or disconnecting and reconnecting the device.
  • If the issue persists, contact ANCEL support.

7. Özellikler

7.1 ANCEL DS500 Elite Bidirectional Scan Tool

• İşlemci: 2.0GHz Cortex-A53 Quad-Core
• İşletim Sistemi: Android 10.0
• Hafıza: 2GB RAM, 32GB ROM
• Görüntülemek: 7-inch screen, 1024x600 resolution
• Pil: 3150mAh, 3.8V
• Bağlantı: Wi-Fi for updates and online support
• Teşhis Fonksiyonları: Full system diagnostics, bidirectional control, 28+ reset services.

7.2 ANCEL BT310 12V/24V Car Battery Tester

• Cilttage Aralık: 12V ve 24V
• CCA Aralığı: 100-2000 CCA
• Desteklenen Pil Türleri: Flooded, AGM (Spiral & Flat Plate), GEL, EFB, Lithium.
• Desteklenen Standartlar: CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, GB.
• Yapılan Testler: Battery Health (SOC, SOH, Voltage, Internal Resistance, Rated/Measured CCA), Cranking Test, Charging Test.

8. Garanti ve Destek

The ANCEL DS500 Elite comes with lifetime free software updates, ensuring your tool remains compatible with evolving vehicle diagnostic systems without additional subscription fees. For technical assistance or support, you can easily contact the professional engineering team through the online chat window available on the DS500 Elite device. Feedback can also be provided via the feedback section on the device to help improve services.