TELECO TVMIO868A02 Remote Control User Manual

Ürün Bittiview

The TELECO TVMIO868A02 is a 2-channel remote control designed for operating up to two automated systems such as gates, garage doors, rolling shutters, or lighting. It operates on the 868.3 MHz frequency and utilizes rolling code technology for secure transmission, preventing unauthorized copying or interference. This compact and robust remote control is suitable for both residential and collective use.

Resim: Ön view of the TELECO TVMIO868A02 remote control, showing its two buttons and sleek design.

Paket İçeriği

• 1 x TELECO TVMIO868A02 Remote Control
• 1 x CR2032 Lithium Battery (pre-installed)
• 1 x Programming Instruction Manual (French)
• 1 x DOMOBIP Keychain (with integrated shopping cart token)

Image: The DOMOBIP keychain, included with the remote control, featuring a shopping cart token.

Kurulum ve Programlama

The TELECO TVMIO868A02 remote control comes with a pre-installed CR2032 battery. Programming can be done via the receiver or by duplication from an existing remote control.

Programming via Receiver

1. Locate the "PROG" or "P1" button on your receiver unit.
2. Press and hold the "PROG" or "P1" button on the receiver.
3. While the receiver is in programming mode, press the desired button on your new TELECO TVMIO868A02 remote control.
4. Release the button on the remote control, then release the button on the receiver. The remote should now be programmed.

Programming by Duplication

This method requires an existing, already programmed TELECO remote control.

1. On the back of the already programmed remote control, locate the "P3" button.
2. Press and hold the "P3" button on the existing remote control.
3. While holding "P3", press the button on the existing remote that you wish to duplicate.
4. Immediately after, press the corresponding button on the new TELECO TVMIO868A02 remote control.
5. Release both buttons. The code should now be transferred to the new remote.

Resim: Arka view of the remote control, displaying the model number TVMIO868A02 and indicating the location of the P3 button for duplication programming.

Collective Residence Mode

In some collective residences (e.g., apartment buildings), the addition of new remote controls may be restricted. In such cases, only the building manager or syndicate administrator can authorize and register new transmitters with the receiver system.

Kullanım Talimatları

Once programmed, each of the two buttons on the TELECO TVMIO868A02 remote control can operate a distinct automated system. Simply press the corresponding button to activate the desired function (e.g., open/close gate, activate lighting).

• Menzil: The remote control offers a range of up to 150 meters in open field conditions. In urban environments, the effective range is typically between 50 and 80 meters, depending on obstacles and interference.
• Güvenlik: The rolling code technology ensures that each transmission is unique, providing enhanced security against signal cloning or unauthorized access.

Resim: Ön view of the remote control, highlighting the two distinct buttons for operating different systems.

Bakım

Pil Değişimi

The remote control is powered by a single CR2032 (3V) lithium battery. When the remote's range decreases or it stops responding, it may be time to replace the battery.

1. Uzaktan kumandayı dikkatlice açın.asing. Refer to the physical instruction manual for specific opening procedures if needed.
2. Eski CR2032 pili çıkarın.
3. Insert a new CR2032 (3V) lithium battery, ensuring correct polarity.
4. Uzaktan kumandayı kapatın.asing güvenli bir şekilde.

Bakım ve Depolama

The remote control has an IP20 protection rating, meaning it is protected against solid objects larger than 12.5mm but has no special protection against water. It is recommended for indoor use or sheltered outdoor environments. Avoid exposing the remote to direct moisture, extreme temperatures, or strong impacts.

Sorun giderme

• Uzaktan kumanda yanıt vermiyor:
  • Pilin değiştirilmesi gerekip gerekmediğini kontrol edin.
  • Ensure the remote is properly programmed to the receiver. Re-attempt programming if necessary.
  • Alıcının açık ve düzgün çalıştığından emin olun.
• Sınırlı aralık:
  • Pili değiştirin.
  • Uzaktan kumanda ile alıcı arasında önemli engellerin (örneğin, kalın duvarlar, metal yapılar) bulunmadığından emin olun.
  • Avoid sources of strong radio interference.
• Uyumsuzluk sorunları:
  • This remote control is specifically designed for TELECO MIO/TVMIO systems operating at 868.3 MHz. It is uyumlu değil with TELECO 433 MHz versions or systems from other brands (e.g., Nice, Somfy, BFT, FAAC).
  • Always verify the frequency (868 MHz) and the exact model reference of your original remote control or receiver before purchase.
• Programming issues in collective residences:
  • If you are in a collective residence, programming new remotes might be centrally controlled. Contact your building manager or syndicate administrator for assistance.

Özellikler

Resim: Yan profile of the remote control, illustrating its slim design.

Uyumluluk

The TELECO TVMIO868A02 remote control is compatible with the TELECO MIO / TVMIO range operating at 868 MHz.

Uyumlu Modeller:

• RCD-868-A04N
• TVRCM868A02
• RCD-868-M04
• TV-LINK and associated models operating at 868.3 MHz

Replaced Models:

• TXP-868-A02
• TVTXP-868-A01 / A02
• I-LIKE and other equivalent references at 868 MHz

Important Incompatibility Notes:

• Bu uzaktan kumanda uyumlu değil with TELECO 433 MHz versions or models with a different appearance.
• Yapar çalışmamak with systems from other manufacturers such as Nice, Somfy, BFT, FAAC, etc.

Resim: Açısal view uzaktan kumandanın gösterimiasinErgonomik tasarımı sayesinde.

Önemli Hususlar

• Always verify the frequency (868 MHz) and the physical appearance of your original remote control to ensure compatibility.
• The exact model reference is often indicated on the back or inside the remote (under the battery).
• If you have any doubts about compatibility, contact customer service with a photo of your current model.
• For collective residences, ensure you have authorization or that the receiver accepts new transmitters before attempting to program.