giriiş
This manual provides essential information for the installation, operation, and maintenance of your QNAP QSW-2104-2T-R2-US 6-Port Unmanaged Switch. Please read this manual thoroughly before using the device to ensure proper setup and optimal performance.
Resim: Ön view of the QNAP QSW-2104-2T-R2-US 6-Port Unmanaged Switch, showing the DC IN port, LED indicators, and six RJ45 ports.
Paket İçeriği
Paketin içinde tüm öğelerin mevcut olduğundan emin olun:
- QNAP QSW-2104-2T-R2-US Unmanaged Switch
- Güç Kaynağı
- Braket Vidaları
- Çapalar
- Ayak pedleri
- Hızlı Kurulum Kılavuzu (QIG)
Kurmak
1. Fiziksel Yerleştirme
- Place the switch on a stable, flat surface.
- Ensure adequate ventilation around the device. Avoid placing it in enclosed spaces or near heat sources.
- The fanless design ensures quiet operation, but proper airflow is still important for heat dissipation.
Image: Diagram illustrating the fanless design and heat dissipation of the QNAP QSW-2104-2T-R2-US switch, showing arrows indicating airflow.
2. Güç Bağlantısı
- Connect the power adapter to the DC IN port on the switch.
- Güç adaptörünü uygun bir elektrik prizine takın.
- The PWR/SYS LED indicator will illuminate when power is supplied.
3. Ağ Bağlantıları
The QSW-2104-2T-R2-US features six RJ45 ports:
- 1-4 numaralı bağlantı noktaları: 2.5GBASE-T RJ45 ports, supporting 2.5Gbps, 1Gbps, and 100Mbps speeds.
- 5-6 numaralı bağlantı noktaları: 10GBASE-T RJ45 ports, supporting 10Gbps, 5Gbps, 2.5Gbps, 1Gbps, and 100Mbps speeds.
- Connect your network devices (e.g., computers, NAS, routers, access points) to the available RJ45 ports using Ethernet cables (CAT5e, CAT6, or CAT7 recommended for optimal performance).
- The switch is unmanaged, meaning it operates on a plug-and-play basis without requiring complex configuration.
Resim: Yakın çekim view of the QNAP QSW-2104-2T-R2-US switch ports, clearly labeling the two 10GbE RJ45 ports and four 2.5GbE RJ45 ports.
Anahtarın Çalıştırılması
LED Göstergeleri
The switch features LED indicators to provide status information:
- GÜÇ/SİSTEM LED'i: Güç durumunu ve sistem etkinliğini gösterir.
- LINK/ACT LEDs (for each port):
- Solid Green: Link established at 2.5G/5G/10G speed.
- Solid Amber: Link established at 100M/1G speed.
- Flashing: Data activity.
- Off: No link or device connected.
- DÖNGÜ LED'İ: Indicates detection of a network loop.
Resim: Ön view of the QNAP QSW-2104-2T-R2-US switch, highlighting the LED indicators for power, system, link/activity, and loop detection.
Tak ve Çalıştır İşlemi
The QSW-2104-2T-R2-US is an unmanaged switch, requiring no software configuration. Simply connect your devices, and the switch will automatically detect and negotiate the optimal speed for each connected device.
Image: Network diagram illustrating various devices like a router, NAS, PC, TV, gaming console, and Wi-Fi access point connected to the QNAP QSW-2104-2T-R2-US switch.
Bakım
- Temizlik: Anahtarın dış yüzeyini temizlemek için yumuşak, kuru bir bez kullanın. Sıvı veya aerosol temizleyiciler kullanmayın.
- Havalandırma: Ensure that the ventilation holes are not obstructed to maintain proper heat dissipation.
- Yazılım: As an unmanaged switch, firmware updates are typically not required or available.
Sorun giderme
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| No power (PWR/SYS LED off) | Güç adaptörü bağlı değil veya arızalı; elektrik prizi çalışmıyor. | Check power connections. Try a different power outlet. Ensure the power adapter is functioning correctly. |
| No link (LINK/ACT LED off) | Ethernet cable disconnected or faulty; connected device is off or faulty. | Ensure the Ethernet cable is securely connected at both ends. Try a different cable. Verify the connected device is powered on and working. |
| Yavaş ağ hızı | Cable quality; device compatibility; network congestion. | Use CAT6 or CAT7 cables for 2.5Gbps/10Gbps connections. Ensure connected devices support the desired speeds. Check for other network activity. |
| LOOP LED is on | Ağ döngüsü tespit edildi. | A network loop occurs when there are redundant paths between devices, which can cause network instability. Disconnect one of the redundant connections to break the loop. The switch has built-in loop detection to help prevent issues. |
Image: Diagram illustrating the loop detection feature of the QNAP QSW-2104-2T-R2-US switch, showing a warning symbol when a network loop is identified.
Özellikler
| Özellik | Detay |
|---|---|
| Örnek | QSW-2104-2T-R2-US |
| Port Sayısı | 6 |
| 2.5GBASE-T RJ45 Ports | 4 (supports 2.5G/1G/100Mb) |
| 10GBASE-T RJ45 Ports | 2 (supports 10G/5G/2.5G/1G/100Mb) |
| Anahtarlama Kapasitesi | 60 Gbps |
| Jumbo Çerçeve Desteği | 12K |
| Tasarım | Fanless, Unmanaged |
| Boyutlar (Y x G x D) | 4 x 6 x 1 inç (yaklaşık) |
| Ağırlık | 1.61 pound (yaklaşık) |
| Arayüz Türü | RJ45 |
| UPC | 885022028153 |
Garanti Bilgileri
QNAP products typically come with a standard manufacturer's warranty. For specific warranty terms and conditions, please refer to the warranty card included in your product packaging or visit the official QNAP webSite. Satın alma belgenizi garanti talepleriniz için saklayın.
This product is noted to come with a 2-year warranty.
Müşteri Desteği
For technical assistance, product information, or support, please visit the official QNAP support website or contact their customer service. Refer to the Quick Installation Guide (QIG) for contact details.
Ayrıca ziyaret edebilirsiniz QNAP Store on Amazon Daha fazla ürün bilgisi ve kaynağı için.
