giriiş
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your GAME 7011-E Sand Filtration System. This system is designed for above-ground pools up to 25,000 gallons, featuring a 16-inch filter tank, a 3/4 HP pump, and a digital timer for automated filtration cycles. Please read all instructions carefully before assembly and use.
Güvenlik Bilgileri
UYARI: Bu talimatlara uyulmaması ciddi yaralanmalara veya ölüme yol açabilir.
- Always disconnect power to the pump before performing any service or maintenance.
- Ensure the electrical supply is protected by a Ground Fault Circuit Interrupter (GFCI).
- Güç kablosu veya fişi hasarlıysa pompayı çalıştırmayın.
- Keep children away from the filtration system during operation.
- The system must be installed on a solid, level surface.
- Güç kablosunu gömmeyin.
- Consult a qualified electrician for electrical connections if unsure.
Paket İçeriği
Montaja başlamadan önce aşağıda listelenen tüm parçaların eksiksiz ve hasarsız olduğundan emin olun.
Image: A visual representation of all components included in the package, such as the six-way valve, sand filter tank, pump, hoses, and hardware.
- Six-Way Valve
- 16-inch Sand Filter Tank
- 16-inch Sand Filter Tank Base
- 16-inch Manifold Tube
- Manifold Lateral Assembly
- Flanş Clamp
- 0.75 HP Pump & Motor Assembly & Base
- kum kalkanı
- Fasteners, Hardware & Gaskets
- Basınç Ölçer
- Sand Filter Tank Drain Plug
- 20", 40" & 120" Hoses
- Süzgeç Sepeti
- Strainer Basket Lid
- Motor Drain Plug
- Gözetleme Camı
Montaj ve Kurulum
Follow these steps for proper assembly and installation of your sand filtration system.
Image: The complete GAME 7011-E Sand Filtration System, including the sand filter tank, pump, and multi-port valve.
- Sistemin Konumlandırılması: Place the filter system on a firm, level surface, preferably concrete, at least 2 feet from the pool. Ensure the location allows for proper drainage when backwashing.
- Assembling the Tank Base: Secure the sand filter tank onto its base.
- Installing Lateral Assembly: Insert the manifold lateral assembly into the bottom of the filter tank. Ensure laterals are spread evenly.
- Adding Filter Sand: Carefully pour approximately 120 pounds of #20 silica sand (0.45-0.55mm) into the filter tank. Ensure the manifold tube remains centered during this process. Fill the tank about two-thirds full.
- Attaching the Six-Way Valve: Place the six-way valve onto the top of the filter tank, aligning the ports. Secure it with the flange clamp, ensuring a tight seal. Use a #3 Phillips screwdriver for the clamp screws and ensure washers are used to prevent damage to the plastic flange. Align the clamp openings with the ridges on the valve.
- Pompanın Bağlanması: Attach the pump to the six-way valve using the provided hoses and fittings. Ensure all connections are tight to prevent leaks. The system uses 1.5-inch inlet and outlet connections.
- Connecting to Pool: Connect the pool's skimmer line to the pump's inlet and the pool's return line to the six-way valve's 'RETURN' port using the provided hoses.
- Installing Pressure Gauge: Screw the pressure gauge into the designated port on the six-way valve.
- Filling the Pump with Water: Before starting, remove the strainer basket lid and fill the pump with water to prime it. Replace the lid securely.
- Elektrik Bağlantısı: Plug the 7.9-meter power cord into a GFCI-protected outlet.
Image: The compact sand filtration system positioned beside an above-ground pool, demonstrating its suitable size for various setups.
Operasyon
The GAME 7011-E Sand Filtration System features a 6-way valve and a digital timer for controlling filtration cycles.
Resim: Bir overview highlighting the pressure gauge for monitoring system performance, the 6-way valve for controlling water flow, and the strainer basket for pre-filtering debris.
6-Way Valve Functions
Always turn off the pump before changing the valve position to prevent damage.
- FİLTRE: Normal filtering mode. Water flows through the sand, trapping debris, and returns to the pool.
- GERİ YIKAMA: Cleans the filter sand by reversing water flow, sending dirty water to waste. Use when pressure gauge reads 8-10 PSI above starting pressure.
- DURULMAK: Used after backwashing to flush out any remaining dirty water from the valve and sand bed to waste before returning to FILTER mode.
- ATIK/KANALİZASYON: Bypasses the filter, sending water directly to waste. Useful for lowering pool water level or vacuuming heavy debris directly to waste.
- DEVRİM: Bypasses the filter, circulating water directly back to the pool. Useful for mixing chemicals without filtering.
- KAPALI: Shuts off all flow to the filter and pump. Use for servicing the pump or filter.
Dijital Zamanlayıcı İşlemi
Image: Close-up of the integrated digital timer, allowing for programmable filtration cycles.
The digital timer allows for automated control of filtration cycles. Refer to the timer's specific instructions for setting daily run times. Ensure the timer is set to provide adequate filtration for your pool size and usage, typically 8-12 hours per day.
Bakım
Regular maintenance ensures optimal performance and longevity of your filtration system.
- Geri yıkama: Perform backwashing when the pressure gauge reads 8-10 PSI above its clean starting pressure, or when water flow to the pool decreases significantly.
- Durulama: Always rinse for 30-60 seconds after backwashing to settle the sand and prevent dirty water from returning to the pool.
- Süzgeç Sepeti Temizliği: Regularly inspect and clean the pump's strainer basket. Turn off the pump, close necessary valves, remove the lid, empty debris, and replace.
- Kum Değişimi: Filter sand typically needs to be replaced every 3-5 years, depending on usage and water chemistry.
- Kışlama: In cold climates, drain all water from the pump and filter tank to prevent freezing damage. Store the pump and valve indoors if possible.
Sorun giderme
This section addresses common issues you might encounter with your sand filtration system.
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Bağlantılardan su sızıyor | Loose fittings, worn O-rings/gaskets, improper clamp hizalama. | Tighten all connections. Inspect and replace O-rings/gaskets if damaged. Ensure flange clamp is correctly aligned and tightened. |
| Kum havuza geri dönüyor | Damaged laterals, incorrect sand type/size, insufficient rinse after backwash. | Check laterals for damage. Ensure correct #20 silica sand is used. Perform a thorough rinse cycle after backwashing. |
| Düşük su akışı/basıncı | Clogged strainer basket, dirty filter sand, air in the system, closed valves. | Clean strainer basket. Backwash and rinse filter. Bleed air from the system. Ensure all necessary valves are open. |
| Pompa emiş yapmıyor | Insufficient water in pump, air leak in suction line, clogged skimmer/main drain. | Fill pump with water. Check all suction line connections for air leaks. Clear any blockages in skimmer or main drain. |
| Excessive pump noise | Lack of water, air in system, cavitation, motor bearing issue. | Ensure pump is fully primed. Check for air leaks. Verify adequate water supply to pump. If noise persists, contact support. |
Özellikler
| Özellik | Detay |
|---|---|
| Marka | OYUN |
| Model Numarası | 7011-D |
| Pompa Beygir Gücü | 0.75 beygir |
| Pompa Debisi | 3,698 GPH |
| Filtre Tankı Boyutu | 16 inç |
| Kum Kapasitesi | 120 pound |
| Max Pool Capacity | 25,000 galona kadar |
| Giriş/Çıkış Bağlantı Boyutu | 1.5 inç |
| Güç Kablosu Uzunluğu | 7.9 metre |
| Boyutlar (U x G x Y) | 15.7 x 26.7 x 30.1 inç |
| Ürün Ağırlığı | 42.7 pound |
| Güvenlik Özelliği | Dahili GFCI |
Garanti ve Destek
The GAME 7011-E Sand Filtration System comes with a 2 yıllık üretici garantisi. For warranty claims, technical assistance, or replacement parts, please contact GAME customer support. Refer to the product packaging or the official GAME webGüncel iletişim bilgileri için siteyi ziyaret edin.
Image: The sand filtration system integrated with a GAME SCG (Saltwater Chlorinator Generator) system, illustrating compatibility.