giriiş
The Wago 221-412 2-Conductor Compact Splicing Connectors are designed for quick, easy, and secure connections of various conductor types and sizes. These connectors feature a lever-actuated design, allowing for tool-free terminations and reliable electrical splices in a compact form factor. They are suitable for a wide range of applications, from general wiring to specialized installations.
A single Wago 221-412 2-conductor compact splicing connector, featuring a clear housing and orange operating levers.
Kurulum ve Yükleme
Proper preparation and installation are crucial for a secure and reliable electrical connection. Follow these steps carefully:
- Tel Hazırlama: Ensure the power supply to the circuit is disconnected before beginning any work. Strip the insulation from the end of each wire to be connected. The recommended stripping length is 11 mm (approximately 0.43 inches). Ensure the stripped conductor is clean and free of damage.
- Open the Lever: For each connection point on the Wago 221 connector, lift the orange operating lever to its fully open position.
- Teli Takın: Insert the stripped end of the prepared wire completely into the open clamping unit until it reaches the backstop. The clear housing allows for visual verification of proper insertion.
- Close the Lever: Push the orange operating lever back down until it is flush with the connector body. This action securely clamps the wire in place.
- Bağlantıyı Doğrulayın: Gently tug on the wire to ensure it is firmly secured and cannot be pulled out. The transparent housing allows for visual inspection of the connection.
Visual guide demonstrating the wire preparation steps: strip wire to 11mm, suitable for 24-12 AWG, and ensure proper insertion.
A three-step visual guide illustrating how to use the Wago 221 connector: Open the lever, Insert the stripped wire, and Close the lever to secure the connection.
A cross-section diagram illustrating correctly stripped and inserted wires within the Wago 221 connector, ensuring a secure connection.
Kullanım Talimatları
The Wago 221-412 connectors are designed for straightforward operation:
- İletken Uyumluluğu: These connectors are suitable for solid, stranded, and fine-stranded conductors ranging from 24 AWG to 12 AWG.
- Tekrar kullanılabilirlik: The lever mechanism allows for easy disconnection and reconnection of wires, making the connectors reusable for modifications or testing. To remove a wire, simply lift the corresponding orange lever, pull out the wire, and then close the lever.
- Test: The connectors feature integrated test slots for voltage testing. These slots allow for convenient testing with a multimeter probe without needing to disconnect the wires.
An illustration indicating the two test slots on the Wago 221 connector, allowing for voltage testing without disconnecting wires.
An illustration detailing the compatibility of Wago 221 connectors with solid, stranded, and flexible wires, specifying 24-12 AWG for the 12 AWG family and 20-10 AWG for the 10 AWG family.
Bakım
Wago 221-412 connectors are designed to be maintenance-free once properly installed. However, periodic visual inspection of connections in critical applications is recommended to ensure continued integrity. Ensure the connectors are not exposed to excessive mechanical stress or environments outside their specified operating conditions.
Sorun giderme
Most issues with Wago 221-412 connectors stem from improper installation. Consider the following if a connection issue arises:
- Gevşek Bağlantı: If a wire feels loose, ensure the orange lever is fully closed. Re-open the lever, re-insert the wire firmly to the backstop, and close the lever again.
- Elektriksel Süreklilik Yok: Verify that the wire insulation was stripped to the correct length (11 mm) and that the bare conductor is fully inserted into the clamping unit. Use the test slots with a multimeter to check for continuity.
- Damaged Connector: If the connector housing or levers appear damaged, replace the connector immediately. Do not use damaged connectors.
- Incorrect Wire Gauge: Ensure the wire gauge used is within the specified range of 24-12 AWG for this model.
Özellikler
| Özellik | Şartname |
|---|---|
| Model Numarası | 221-412 |
| İletken Sayısı | 2 |
| Anma Hacmitage | 450V AC |
| Anma Akımı | 20 Amps |
| Tel Ölçer Aralığı | 24 - 12 AWG (Solid, Stranded, Fine-Stranded) |
| Sıyırma Uzunluğu | 11 mm (0.43 inç) |
| Bağlayıcı Türü | Clamp (Lever-Actuated) |
| Malzeme | Plastik |
| Renk | Clear (housing), Orange (levers) |
| Ürün Boyutları | 0.52 x 0.52 x 0.33 inç (yaklaşık) |
Diagram showing the dimensions of the Wago 221-412 connector: 0.732 inches in length, 0.52 inches in width, and 0.327 inches in height.
Garanti ve Destek
For specific warranty information, please refer to the official WAGO website or contact WAGO customer support directly. WAGO products are manufactured to high-quality standards, and support is available for product inquiries and technical assistance.
WAGO Contact Information:
- Visit the official WAGO webDestek kaynakları ve iletişim bilgileri için siteyi ziyaret edin.
- Refer to the product packaging for any specific warranty statements or regional contact information.
