WORKPRO 7.2V Cordless Hot Melt Glue Gun User Manual

1. Giriş

Thank you for choosing the WORKPRO 7.2V Cordless Hot Melt Glue Gun. This rechargeable glue gun is designed for various crafting, DIY projects, and repair tasks, offering fast preheating, long-lasting battery life, and convenient USB Type-C charging. Its automatic power-off feature enhances safety and conserves energy. Please read this manual thoroughly before use to ensure safe and optimal operation.

2. Güvenlik Talimatları

• Hot Nozzle: İşlem sırasında nozul ve erimiş yapıştırıcı çok ısınır. Yanıkları önlemek için ciltle doğrudan temasından kaçının.
• Yanıcı malzemeler: Do not use the glue gun near flammable liquids, gases, or materials.
• Çocuklar: Keep out of reach of children. Adult supervision is required if children are using the device.
• Şarj: Use only the provided USB A to USB C cable for charging. Do not use USB C to USB C cables, as they are not supported.
• Depolamak: Store the glue gun in a dry, safe place when not in use. Ensure it is completely cooled before storing.
• Otomatik Kapanma: The device features an automatic power-off function after 10 minutes of idle use. This is a safety feature and does not replace manual power-off when finished.
• Malzeme: The glue gun is constructed from flame-retardant material with good insulation for enhanced safety.

3. Paket İçeriği

Paketinizde tüm öğelerin mevcut olduğundan emin olun:

• 1 x WORKPRO 7.2V Cordless Hot Melt Glue Gun
• 20 x Premium Mini Glue Sticks
• 1 x USB Type-C Charging Cable (USB A to USB C)

4. Kurulum

4.1 Charging the Glue Gun

Before first use, fully charge the glue gun.

1. Connect the provided USB A to USB C charging cable to the Type-C port located at the bottom of the glue gun handle.
2. Plug the USB A end into a compatible power source (e.g., phone charger, laptop/PC, car charger, power bank).
3. The LED indicator lights on the handle will show charging status. Once fully charged, the lights will indicate a full battery.

Note: The glue gun does not support USB C to USB C cable charging. Use only the original USB A to USB C cable.

Figure 1: Charging the WORKPRO Cordless Hot Melt Glue Gun.

4.2 Yapıştırıcı Çubuğun Takılması

1. Ensure the glue gun is turned off and cooled down.
2. Insert a mini glue stick (7mm diameter) into the round opening at the back of the glue gun.
3. Push the glue stick gently until it stops. Do not force it.

5. Kullanım Talimatları

5.1 Çalıştırma ve Ön Isıtma

1. Press and hold the power button on top of the glue gun for approximately 3 seconds until the LED indicator lights on the handle illuminate.
2. The glue gun will begin to preheat. The LED indicator lights will blink during preheating.
3. Preheating takes approximately 30 seconds. Once the glue gun reaches its working temperature, the LED indicator lights will stop blinking and remain solid. The device is now ready for use.

Figure 2: Fast preheating feature of the glue gun.

5.2 Yapıştırıcı Uygulama

1. Once the glue gun is preheated (solid LED lights), aim the nozzle at the desired surface.
2. Gently squeeze the trigger to dispense melted glue. The glue output speed is approximately 0.18oz/5g per minute.
3. Apply glue as needed. The low-leakage nozzle design helps minimize dripping.
4. After applying glue, release the trigger.

Figure 3: Step-by-step guide for using the glue gun.

5.3 Otomatik Kapanma

The glue gun will automatically shut down after 10 minutes of inactivity to conserve battery life and enhance safety. To resume operation, simply press and hold the power button again.

5.4 Using the Vertical Stand

The glue gun features a stable vertical stand integrated into its design, allowing it to stand upright on a flat surface. This prevents the hot nozzle from touching your work surface and reduces glue spillage when not actively dispensing glue.

Figure 4: The glue gun's stable standing base design.

6. Bakım

• Temizlik: Ensure the glue gun is turned off and completely cooled before cleaning. Use a soft, dry cloth to wipe the exterior. Do not use abrasive cleaners or solvents.
• Meme Bakımı: Do not attempt to clean the nozzle while it is hot. Any hardened glue around the nozzle can be carefully removed once the gun is cold.
• Depolamak: Store the glue gun in a cool, dry place, away from direct sunlight and extreme temperatures.
• Akü Bakımı: For optimal battery life, charge the glue gun every 3-6 months even if not in regular use.

7. Sorun Giderme

• Glue not dispensing: Ensure the glue gun is fully preheated (solid LED lights). Check if a glue stick is properly inserted and if it has reached the heating chamber.
• Glue gun not heating: Verify the battery is charged. If the LED lights are not on or are blinking erratically, recharge the device.
• Pil şarj olmuyor: Ensure the USB A to USB C cable is correctly connected to both the glue gun and a compatible power source. Confirm the power source is active. Remember, USB C to USB C cables are not supported.
• Excessive dripping: While designed for low leakage, some minimal dripping can occur. Ensure the glue gun is standing upright on its base when not in active use.

8. Özellikler

9. Garanti ve Destek

For warranty information or technical support, please refer to the documentation included with your product or contact WORKPRO customer service directly. Keep your purchase receipt as proof of purchase.