Jaycar Digitech QC1938 100MHz Digital Oscilloscope User Manual

1. Giriş

This manual provides detailed instructions for the safe and effective operation of your Jaycar Digitech QC1938 100MHz Digital Oscilloscope. Please read this manual thoroughly before using the device to ensure proper setup, operation, and maintenance. Retain this manual for future reference.

2. Güvenlik Bilgileri

Observe the following safety precautions to prevent injury and avoid damage to the instrument or any products connected to it.

• Güç Kaynağı: Connect the oscilloscope only to the power source specified in this manual.
• Topraklama: Ensure the instrument is properly grounded to prevent electric shock.
• Problar: Use only probes supplied or recommended by the manufacturer. Ensure probes are rated for the voltagÖlçülmekte olan.
• Havalandırma: Havalandırma açıklıklarını kapatmayın. Cihazın etrafında yeterli hava akışı olduğundan emin olun.
• Çevre: Operate the oscilloscope in a dry environment. Avoid exposure to moisture, dust, or extreme temperatures.
• Servis: Refer all servicing to qualified service personnel. Do not attempt to repair the instrument yourself.

3. Paket İçeriği

Aşağıda listelenen tüm öğelerin paketinizde mevcut olduğundan emin olun:

• Jaycar Digitech QC1938 Digital Oscilloscope
• 10:1 Passive Probe with 1.5m lead
• 2 x BNC to Clip Test Leads
• USB kablosu
• Güç kablosu
• Kullanım Kılavuzu (bu belge)

4. Ürün Bittiview

The Jaycar Digitech QC1938 is a 100MHz Digital Oscilloscope designed for precise electronic measurements. It features a 7-inch color LCD screen, two independent channels, and a built-in waveform generator.

Temel Özellikler:

• 7-inch TFT color LCD screen with 800 x 480 pixel resolution
• İki bağımsız giriş kanalı
• 100MHz bandwidth and 1GSa/s sampling oranı
• 8M memory depth (single channel)
• Integrated 25MHz waveform generator (Sine, Square, Ramp, Exponential, Noise, DC)
• Auto scale function for automatic sine and square wave detection
• 14 trigger modes including Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, and IIC
• 5 serial protocol triggers and decodes: RS232/UART, I2C, SPI, CAN, and LIN
• Two 3-digit digital voltmeters and a 6-digit hardware frequency indicator
• 32 types of auto measurements with real-time statistics
• USB Host/Device interface for computer control and data storage

5. Kurulum

5.1 Güç Bağlantısı

1. Connect the supplied power lead to the power input on the rear panel of the oscilloscope.
2. Plug the other end of the power lead into a grounded AC power outlet.
3. Osiloskopu açmak için ön paneldeki güç düğmesine basın.

5.2 Prob Bağlantısı

1. Connect the BNC connector of the passive probe to either Channel 1 (CH1) or Channel 2 (CH2) input on the front panel.
2. Attach the ground clip of the probe to the circuit's ground point.
3. Connect the probe tip to the test point in your circuit.
4. Ensure the probe's attenuation setting (e.g., 1X or 10X) matches the setting on the oscilloscope for accurate readings.

6. Kullanım Talimatları

6.1 Temel İşlemler

• Auto Scale: Press the 'AUTO SET' button to automatically adjust vertical, horizontal, and trigger settings for a stable waveform display. This function detects sine and square waves automatically.
• Vertical Controls (VOLTS/DIV, POSITION): Use the VOLTS/DIV knobs to adjust the vertical scale (voltage per division) for each channel. The POSITION knobs shift the waveform vertically.
• Horizontal Controls (SEC/DIV, POSITION): Use the SEC/DIV knob to adjust the horizontal scale (time per division). The horizontal POSITION knob shifts the waveform horizontally.
• Tetikleme Seviyesi: Adjust the 'TRIGGER LEVEL' knob to set the voltage level at which the oscilloscope captures a waveform.

6.2 Gelişmiş İşlev

• Dalga Formu Üreteci: Access the waveform generator menu to select and configure output waveforms such as Sine, Square, Ramp, Exponential, Noise, and DC. Connect the 'WAVE GEN' output to your circuit.
• Tetikleme Modları: Utilize the 14 available trigger modes (Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC) to capture specific events. Select modes via the 'TRIGGER' menu.
• Seri Protokol Kod Çözme: The oscilloscope supports decoding for RS232/UART, I2C, SPI, CAN, and LIN protocols. Configure these settings in the 'DECODE' menu to view decoded data.
• Ölçümler: The device offers 32 types of automatic measurements with real-time statistics (maximum, minimum, standard deviation, etc.). Access these via the 'MEASURE' menu.
• USB Bağlantısı: Connect a USB thumb drive to the USB Host port to save oscilloscope setups, waveforms, reference waveforms, CSV files, and images. The USB Device port allows for remote control from a computer using SCPI commands.

7. Bakım

7.1 Temizlik

Aleti temizlemek için yumuşak bir bez kullanın.ampHafif bir deterjan çözeltisiyle durulayın. Aşındırıcı temizleyiciler veya yüzeye zarar verebilecek çözücüler kullanmayın.asing veya ekran. Temizlemeden önce cihazın kapalı ve fişinin çekilmiş olduğundan emin olun.

7.2 Depolama

When not in use, store the oscilloscope in a dry, dust-free environment away from direct sunlight and extreme temperatures. Use the original packaging or a suitable case for protection during transport.

8. Sorun Giderme

If you encounter issues with your oscilloscope, refer to the following common problems and solutions:

Bu çözümleri denedikten sonra sorun devam ederse lütfen müşteri desteğiyle iletişime geçin.

9. Özellikler

10. Garanti ve Destek

Garanti bilgileri ve teknik destek için lütfen satın alma sırasında verilen belgelere bakın veya satıcınızla iletişime geçin. Garanti talepleri için satın alma belgenizi saklayın.