QIACHIP EV1527 Rf433m Kablosuz Uzaktan Kumanda Vericileri Kullanım Kılavuzu

1. Giriş

This manual provides comprehensive instructions for the QIACHIP EV1527 Rf433m Wireless Remote Transmitters. These transmitters are designed to be used with a compatible 12V 1-channel wireless receiver (receiver not included) to control various electronic devices remotely. Please read this manual carefully before use to ensure proper setup and operation.

Image 1.1: Three QIACHIP EV1527 Rf433m Wireless Remote Transmitters. Each remote features two buttons, labeled 'A' and 'B', and an attached metal keychain clip.

2. Ürün Bittiview

The QIACHIP EV1527 Rf433m Wireless Remote Transmitter is a compact and ergonomic device designed for convenient remote control. Each remote features two silicone buttons and an indicator light.

2.1 Bileşenler

• Silicone Buttons (A and B): Used to send control signals to the paired receiver.
• Gösterge Işığı: Illuminates when a button is pressed, indicating signal transmission.
• Chrome Bezel: Provides a durable and aesthetic finish.
• Metal Keychain: Allows for easy attachment to keys or other items.

Image 2.1: Diagram illustrating the key components of the remote control, including the silicone buttons (A and B), indicator light, chrome bezel, and metal keychain.

2.2 Çalışma Aralığı

These remote transmitters offer a wide operating range, typically up to 100 meters in an open, unobstructed area. Actual range may vary depending on environmental factors and obstacles.

Image 2.2: Illustration depicting the effective operating range of the wireless remote, showing a signal reaching up to 100 meters in an open environment.

3. Kurulum

3.1 Pil Kurulumu

The remote control requires one CR2032 button cell battery. The battery is typically pre-installed, but if replacement is needed or if the remote is not functioning, follow these steps:

1. Uzaktan kumandayı dikkatlice açınasing. This usually involves prying apart the two halves of the remote, often near the keychain loop.
2. Locate the battery compartment on the circuit board.
3. Eski CR2032 pili kutuplarına dikkat ederek çıkarın.
4. Yeni bir CR2032 pili pozitif (+) tarafı yukarı bakacak şekilde takın.
5. Close the remote casing güvenli bir şekilde.

Resim 3.1: View of the remote's internal circuit board, showing the placement of the CR2032 button cell battery.

3.2 Alıcıyla Eşleştirme

These transmitters are designed to work with a compatible QIACHIP 12V 1-channel wireless receiver (not included). A single receiver can pair with up to 20 remotes. The pairing process typically involves the following steps, though specific details may vary based on your receiver model:

1. Alıcıyı Açın: Ensure your 12V 1-channel wireless receiver is powered on.
2. Clear Existing Programming (Recommended): To prevent conflicts, it is often recommended to clear any previous pairings on the receiver. This is typically done by pressing the receiver's learning button (often a small button on the circuit board) 8 times. The receiver's indicator light should flash rapidly and then turn off, confirming the memory has been cleared.
3. Öğrenme Moduna Girin: Press the receiver's learning button once or twice, depending on the desired operating mode (e.g., momentary, toggle, latched). The receiver's indicator light will illuminate steadily, indicating it is in learning mode.
4. İletim Sinyali: While the receiver's indicator light is steady, press the desired button (A or B) on your QIACHIP remote transmitter. The remote's indicator light will flash.
5. Eşleştirmeyi Onayla: The receiver's indicator light should flash a few times and then turn off, confirming successful pairing.
6. Test İşlevselliği: Press the paired button on the remote to ensure the receiver responds as expected.

Not: Refer to your specific receiver's instruction manual for precise pairing procedures and mode selection (e.g., momentary, toggle, latched).

4. Çalıştırma

Once your QIACHIP EV1527 remote transmitter is successfully paired with a compatible receiver, operation is straightforward:

• Press Button A or B: Simply press the 'A' or 'B' button on the remote to send a signal to the receiver.
• Gösterge Işığı: The small indicator light on the remote will illuminate briefly when a button is pressed, confirming that a signal is being transmitted.
• Receiver Response: The paired receiver will execute the programmed action (e.g., turn a device on/off, open/close a garage door) according to its configured mode (momentary, toggle, or latched).

5. Bakım

5.1 Pil Değişimi

If the remote's indicator light becomes dim or fails to illuminate, or if the remote's range decreases significantly, it may be time to replace the battery. The remote uses one CR2032 button cell battery.

1. Open the remote casinBölüm 3.1'de açıklandığı gibi g.
2. Eski CR2032 pili dikkatlice çıkarın.
3. Insert a new CR2032 battery, ensuring the positive (+) side is facing up.
4. Close the remote casing güvenli bir şekilde.

Not: In some rare cases, after battery replacement, the remote may need to be re-paired with the receiver. Follow the pairing instructions in Section 3.2 if necessary.

6. Sorun Giderme

• Uzaktan Kumanda Yanıt Vermiyor:
  • Check the battery: Ensure the CR2032 battery is correctly installed and has sufficient charge. Try replacing it with a new battery.
  • Receiver Power: Verify that your 12V 1-channel wireless receiver is properly powered and functioning.
  • Re-pairing: Attempt to re-pair the remote with the receiver following the steps in Section 3.2.
  • Remote Reset: If a new remote or a remote after battery change is not pairing, try removing and reinserting the battery in the remote to perform a soft reset, then attempt pairing again.
• Limited Operating Range:
  • Obstructions: Ensure there are no significant physical obstructions (e.g., thick walls, metal objects) between the remote and the receiver.
  • Antenna: Verify that the receiver's antenna (if applicable) is fully extended and unobstructed.
  • Interference: Minimize potential sources of radio frequency interference in the vicinity.

7. Özellikler

Image 7.1: Diagram showing the approximate dimensions of the remote control: 6.1 cm in length and 2.9 cm in width.

8. Garanti ve Destek

8.1 Garanti Bilgileri

Specific warranty details for the QIACHIP EV1527 Rf433m Wireless Remote Transmitters are not provided in the product documentation. For information regarding warranty coverage, please contact the seller or manufacturer directly.

8.2 Müşteri Desteği

For further assistance, technical support, or inquiries, please contact QIACHIP customer service through their official channels or the retailer where the product was purchased.

You can visit the QIACHIP Store for more information: QIACHIP Store on Amazon