1. Ürün Bittiview
The eSUN eBOX Lite is an upgraded filament dryer box designed to maintain optimal conditions for 3D printing filaments. It effectively removes moisture, preventing common printing issues such as stringing, clogging, and poor adhesion. This device also functions as a filament storage box and spool holder, providing a comprehensive solution for filament management.
Key features include efficient heating, even temperature distribution, low-noise operation, and broad compatibility with various filament types and spool sizes.
Figure 1: eSUN eBOX Lite Filament Dryer Box with a red filament spool inside.
2. Paket İçeriği
Paketin içinde tüm öğelerin mevcut olduğundan emin olun:
- eBOX Lite Dryer Box
- Güç Adaptörü (ABD Fişi)
- User Manual (this document, and a physical copy)
- Filament Outlet Tube/Bayonet
Figure 2: Illustration of the eBOX Lite and its included accessories.
3. Kurulum Talimatları
- Atama: Place the eBOX Lite on a stable, flat surface away from direct sunlight, heat sources, and excessive humidity. Ensure adequate ventilation around the unit.
- Güç Bağlantısı: Connect the provided power adapter to the DC input port on the back of the eBOX Lite. Plug the adapter into a standard US power outlet (AC100-240V ~ 50/60Hz).
- Filament Yükleniyor:
- Open the transparent lid of the eBOX Lite.
- Place your filament spool onto the internal rollers. Ensure the spool rotates freely. The maximum compatible spool size is Φ200mm (diameter) x 73mm (height).
- Thread the filament through the designated outlet hole on the lid. If using the outlet conduit, attach it to the hole and thread the filament through it.
- Kapağı sıkıca kapatın.
Figure 3: Visual guide for connecting power and loading filament.
4. Kullanım Talimatları
The eBOX Lite features a simple control panel with a display and buttons for setting temperature and time.
4.1. Kontrol Paneli Üzerindeview
- Görüntülemek: Shows current settings (temperature level, time remaining).
- Mod Düğmesi: Used to cycle between temperature setting mode and time setting mode.
- Yukarı/Aşağı Düğmeleri: Used to adjust values (temperature level, time).
4.2. Sıcaklık ve Zaman Ayarı
- Güç Açık: After connecting the power, the display will light up.
- Set Temperature Level:
- Basın Mod button once to enter temperature setting mode. The display will show a number (1, 2, or 3).
- Kullanın Yukarı/Aşağı buttons to select the desired temperature level based on your filament type:
- Seviye 1: Approximately 40°C (suitable for PLA/PLA+)
- Seviye 2: Approximately 50°C (suitable for ABS/ABS+/PETG)
- Seviye 3: Approximately 55°C (suitable for PVA/Nylon/PC)
- Basın Mod button again to confirm the temperature level and proceed to time setting.
- Set Heating Time:
- The display will now show the time setting (e.g., "00.0h").
- Kullanın Yukarı/Aşağı buttons to set the desired heating duration from 0 to 18 hours. For optimal drying, eSUN recommends at least 2 hours for most filaments.
- Basın Mod button again to start the drying process. The display will show the remaining time.
The eBOX Lite will maintain the set temperature and humidity throughout the drying cycle. Once the time expires, the heating will stop, but the box will continue to provide a dry storage environment.
Figure 4: Recommended temperature levels and corresponding filament types.
Figure 5: Graph illustrating humidity reduction over time during drying.
5. Bakım
Regular maintenance ensures the longevity and optimal performance of your eBOX Lite.
- Temizlik: Wipe the exterior of the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure the unit is unplugged before cleaning.
- İç Temizlik: Periodically check the inside of the box for any dust or filament debris. Use a soft brush or compressed air to remove any accumulation.
- Depolamak: Uzun süre kullanılmayacaksa, cihazın fişini çekin ve serin ve kuru bir yerde saklayın.
6. Sorun Giderme
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Cihaz açılmıyor. | Güç adaptörü bağlı değil veya arızalı; elektrik prizi sorunu. | Ensure power adapter is securely connected. Try a different power outlet. Check if the power adapter is damaged. |
| Filament not drying effectively. | Incorrect temperature level set; insufficient drying time; lid not closed properly. | Verify the correct temperature level for your filament type. Increase drying time (e.g., to 4-6 hours or more for very wet filament). Ensure the lid is fully closed. |
| Ekran boş veya tepkisiz. | Geçici yazılım hatası; elektrik kesintisi. | Unplug the device, wait 30 seconds, then plug it back in. If the issue persists, contact customer support. |
| Filament spool does not rotate smoothly. | Spool too large or not seated correctly; debris on rollers. | Ensure spool dimensions are within specifications (Φ200mm x 73mm). Re-seat the spool. Clean the rollers. |
7. Özellikler
| Parametre | Değer |
|---|---|
| Model Numarası | eBox-Lite-US |
| İç Sıcaklık Aralığı | 40°C - 55°C |
| Hot Plate Temperature | 105°C - 118°C |
| Anma Gücü | AC100-240V ~ 50/60Hz |
| Güç Çıkışı | DC24V ~ 2A |
| Isıtıcının Gücü | 35W |
| Ürün Ağırlığı | 0.75 kg (1.65 pound) |
| Ürün Boyutu | 215x104x238.5 mm |
| Paket Boyutları | 10.91 x 10 x 5.51 inç |
| Max Spool Capacity | Φ200mm (diameter) x 73mm (height) |
| Compatible Filament Diameter | 1.75mm / 2.85mm / 3.00mm |
| Malzeme Türü | Polikarbonat |
Şekil 6: Ayrıntılı ürün özellikleri ve paket içeriği.
8. Garanti ve Destek
For warranty information and technical support, please refer to the official eSUN webSite üzerinden satın alabilir veya doğrudan müşteri hizmetleriyle iletişime geçebilirsiniz. Satın alma belgenizi saklayın.
Ayrıca ek kaynaklara ve kullanım kılavuzunun PDF versiyonuna şu adresten ulaşabilirsiniz: eSUN eBOX Lite User Manual (PDF)
