1. Giriş
This manual provides essential information for the installation, operation, and maintenance of the BANNER ENGINEERING S18AW3FF50 EZ-Beam S18 Series Photoelectric Sensor. This sensor is designed for reliable object detection in industrial environments, featuring a 50 mm range, 20-250VAC input, and SPST solid-state light operate output.
Figure 1: BANNER ENGINEERING S18AW3FF50 Photoelectric Sensor with coiled cable.
2. Kurulum ve Kurulum
Doğru kurulum, en iyi performans ve güvenlik için çok önemlidir. Lütfen bu adımları dikkatlice izleyin.
2.1 Paketin Açılması ve Muayene
- Carefully remove the sensor from its packaging.
- Inspect the sensor for any visible damage that may have occurred during shipping.
- Paketleme fişinde listelenen tüm bileşenlerin mevcut olduğunu doğrulayın.
2.2 Sensörü Monte Etme
The S18AW3FF50 sensor is designed for easy mounting. Ensure the mounting surface is stable and free from excessive vibration.
- Select a mounting location that provides clear line-of-sight for the sensor's detection range (50 mm).
- Secure the sensor using appropriate mounting hardware (not included). The sensor features a threaded barrel for secure attachment.
- Ensure the sensor is oriented correctly for the intended detection application.
Şekil 2: Yan view of the S18AW3FF50 sensor, showing the threaded barrel and cable.
2.3 Elektrik Bağlantıları
UYARI: Disconnect all power before making electrical connections to prevent electric shock or damage to the equipment.
The S18AW3FF50 operates on 20-250VAC input and provides an SPST Solid-State Light Operate output. The sensor comes with a 2M (6.5FT) cable.
| Tel Rengi | İşlev |
|---|---|
| Kahverengi | AC Line (L1) |
| Mavi | AC Neutral (L2) |
| Siyah | Output (SPST Light Operate) |
Connect the sensor wires to the control circuit according to the provided wiring diagram and local electrical codes. Ensure all connections are secure.
Figure 3: S18AW3FF50 sensor showing the cable with exposed wires for electrical connection.
3. Operasyon
Once installed and wired, the S18AW3FF50 sensor is ready for operation.
3.1 Açma
Apply power to the sensor (20-250VAC). The sensor will typically have an indicator LED (if present) to show power status and output state.
3.2 Detection Principle
The S18AW3FF50 is a photoelectric sensor operating in a fixed field mode. It emits a light beam and detects objects based on the reflection or interruption of this beam. The "Light Operate" output means the output will be active when light is received by the sensor (i.e., when an object is detected or not detected, depending on the specific fixed field configuration).
3.3 Menzil ve Performans
The sensor has a specified detection range of 50 mm. Ensure that objects to be detected fall within this range for reliable operation. Environmental factors such as dust, moisture, and ambient light can affect performance.
4. Bakım
The S18AW3FF50 sensor is designed for low maintenance. Regular checks can ensure long-term reliable operation.
4.1 Temizlik
- Periodically clean the sensor lens and housing to remove dust, dirt, or debris that may accumulate and interfere with detection.
- Use a soft, lint-free cloth and a mild cleaning solution if necessary. Avoid abrasive cleaners or solvents.
4.2 Cable and Connection Inspection
- Regularly inspect the sensor cable for any signs of wear, cuts, or damage.
- Check electrical connections to ensure they remain secure and free from corrosion.
5. Sorun Giderme
This section provides solutions to common issues encountered with the S18AW3FF50 sensor.
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Sensor not powering on | No power supply; Incorrect wiring; Damaged sensor. | Verify power supply (20-250VAC); Check wiring against Table 1; Replace sensor if damaged. |
| Sensör nesneleri algılamıyor. | Object out of range (50 mm); Dirty lens; Misalignment; Ambient light interference. | Ensure object is within 50 mm range; Clean sensor lens; Realign sensor; Shield sensor from strong ambient light. |
| Aralıklı algılama | Vibration; Loose connections; Fluctuating power. | Secure sensor mounting; Check all electrical connections; Ensure stable power supply. |
6. Özellikler
Key technical specifications for the BANNER ENGINEERING S18AW3FF50 Photoelectric Sensor.
- Modeli: S18AW3FF50
- Seri: EZ-Beam S18 Series
- Algılama Aralığı: 50 mm
- Giriş Voltage: 20-250VAC
- Çıktı Türü: SPST Solid-State Light Operate
- Kablo Uzunluğu: 2 milyon (6.5 fit)
- Sensör Tipi: Photoelectric, Fixed Field
- Üretici: BANNER ENGINEERING
- ASIN: B07RZTBRLS
- İlk Mevcut Tarih: 3 Aralık 2021
7. Garanti ve Destek
For warranty information and technical support, please contact BANNER ENGINEERING directly or refer to their official webalan.
İade politikasi: The product may be subject to a return policy of 30 days for refund/replacement, as per the seller's terms.
Üretici: BANNER ENGINEERING
Daha fazla yardım için şu adresi ziyaret edin: BANNER ENGINEERING official webalan.
