Ürün Bittiview
The Emtek 7103 Passage Set is a high-quality knobset designed for doors that do not require a locking mechanism, such as closet doors, hallway doors, or pantry doors. This set includes a Madison Black Knob and a #3 Wrought Steel Rosette with a Flat Black Steel (FBS) finish. It is manufactured by Emtek and includes a standard rotation latch and strike plate. The knobset is designed for a standard 2-1/8 inch door preparation. The standard latch is for a 2-3/8 inch backset, with a 2-3/4 inch backset available if specified.
This image displays the Emtek 7103 Passage Set, featuring a round Madison Black Knob mounted on a rectangular Flat Black Wrought Steel Rosette. The knob has a smooth, glossy black finish, contrasting with the textured matte black finish of the rosette.
Kurulum ve Yükleme
This section provides instructions for the proper setup and installation of your Emtek 7103 Passage Set.
Başlamadan Önce
- Ensure all components are present: knobset, rosette, latch, strike plate, and mounting screws.
- Verify door thickness and backset requirements. Standard backset is 2-3/8 inches. If 2-3/4 inches is required, ensure you have the correct latch.
- Gerekli aletler: Yıldız tornavida, mezura, kurşun kalem.
Kurulum Adımları
- Kapıyı Hazırlayın: Ensure the door has a standard 2-1/8 inch bore hole for the knobset and a 1-inch bore hole for the latch.
- Mandalı takın: Insert the latch into the edge of the door, ensuring the bevel faces the door frame. Secure with screws.
- Install the Exterior Knob/Rosette: Place the exterior knob and rosette assembly through the 2-1/8 inch bore hole, aligning the spindle with the latch mechanism.
- Install the Interior Knob/Rosette: Place the interior knob and rosette assembly onto the spindle, aligning the mounting posts with the holes on the exterior rosette.
- Meclisi Güvence Altına Alın: Insert and tighten the mounting screws through the interior rosette into the exterior rosette. Do not overtighten.
- Çarpma Plakasını Takın: Mark and chisel the door frame for the strike plate. Secure the strike plate with screws, ensuring the latch engages smoothly.
- Test İşlemi: Rotate the knobs to ensure the latch retracts and extends freely. Check for smooth operation from both sides of the door.
Kullanım Talimatları
The Emtek 7103 Passage Set is designed for doors that do not require locking, such as closet doors, hallway doors, or pantry doors. It allows for free passage from both sides at all times.
- To open the door, simply turn the knob in either direction. The latch bolt will retract, allowing the door to open.
- To close the door, push the door shut. The latch bolt will automatically engage with the strike plate, holding the door closed.
Bakım
Proper maintenance will ensure the longevity and smooth operation of your Emtek 7103 Passage Set.
- Temizlik: Clean the knob and rosette surfaces with a soft, damp cloth. Avoid abrasive cleaners, solvents, or polishes that may damage the finish.
- Yağlama: Periodically apply a small amount of silicone-based lubricant to the latch mechanism to ensure smooth operation. Do not use oil-based lubricants as they can attract dust and grime.
- Sıkma Vidaları: Over time, mounting screws may loosen. Periodically check and gently tighten any loose screws to maintain stability. Do not overtighten.
- Denetleme: Regularly inspect the knobset for any signs of wear, damage, or misalignment.
Sorun giderme
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Knob is loose or wobbly. | Montaj vidaları gevşek. | Tighten the mounting screws on the interior rosette. |
| Latch does not retract smoothly. | Yağlama eksikliği; mekanizmada biriken kalıntılar. | Apply silicone-based lubricant to the latch bolt. Clean any visible debris. |
| Door does not close properly or rattles. | Strike plate misalignment; worn latch. | Adjust the strike plate position. If latch is worn, consider replacement. |
| Knob is stiff to turn. | Spindle misalignment; internal mechanism friction. | Loosen mounting screws slightly, adjust knob position, then retighten. Lubricate internal mechanism if accessible. |
Özellikler
- Modeli: Emtek 7103 Passage Set
- Malzeme: Wrought Steel
- Topuz Stili: Madison Black Knob
- Rosette Style: #3 Rosette
- Sona ermek: Flat Black Steel (FBS)
- Kapı Hazırlığı: Standard 2-1/8" bore hole
- Arka set: Standard 2-3/8" (2-3/4" available upon request)
- UPC: 751125555226
Garanti ve Destek
Emtek products are manufactured to high-quality standards. For specific warranty information regarding your Emtek 7103 Passage Set, please refer to the documentation provided with your purchase or visit the official Emtek webSite. Garanti şartları ve koşulları değişiklik gösterebilir.
For technical support, product inquiries, or assistance with installation or troubleshooting, please contact Emtek customer service directly. Their contact information can typically be found on their official websitede veya ürün ambalajının içinde.
Üretici: emtek
Resmi Webalan: www.emtek.com
