1. Giriş
The Pedrollo Easy Press-1 is an electronic pressure controller designed for single-phase electric pumps. This device automates the starting and stopping of the pump based on water demand (opening and closing of taps). It incorporates microprocessor logic to protect the pump from dry running, offering both automatic and manual reset functions. Furthermore, it safeguards the electric pump against frequent starts caused by minor leaks in the system. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Easy Press-1 controller.
2. Güvenlik Bilgileri
Please read all safety instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, serious injury, or property damage.
- Elektriksel Güvenlik: Always disconnect power before performing any electrical connections or maintenance. Ensure all wiring complies with local electrical codes.
- Profesyonel Kurulum: Kurulum yalnızca kalifiye personel tarafından yapılmalıdır.
- Su Basıncı: Cihaz için belirtilen maksimum çalışma basıncını aşmayın.
- Sıcaklık Sınırları: Operate the device only within the specified minimum and maximum operating temperatures.
- Koruma: The device has an IP65 protection rating, meaning it is protected against dust and low-pressure water jets. However, it should not be submerged.
3. Ürün Bittiview
The Pedrollo Easy Press-1 is an orange-colored electronic unit with integrated pressure sensors and control logic. It features clear indicators for its operational status.
Şekil 1: Pedrollo Electronic Pressure Controller. This image displays the general appearance of a Pedrollo electronic pressure controller, an orange unit with a blue label. The label indicates "EASY PRESS II Electronic", along with indicators for "POWER" and "STATUS", and a "START/STOP" button. Technical markings include "MADE IN ITALY Max 10 bar IP 65 CE PEDROLLO". Please note that while this image shows "EASY PRESS II", the manual refers to the "Easy Press-1" model.
3.1. Bileşenler ve Göstergeler
- Güç Göstergesi: (Green LED) Illuminates when the device is powered.
- Durum Göstergesi: (Red LED) Indicates operational status or fault conditions, such as dry running.
- Başlat/Durdur Düğmesi: Used for manual pump control and resetting after a dry-run protection event.
- Giriş/Çıkış Bağlantıları: Threaded connections for integration into the water system.
4. Teknik Özellikler
| Parametre | Değer |
|---|---|
| Örnek | Easy Press-1 (Art.50066/115) |
| Güç Kaynağı Hacmitage | 230 Volt (single-phase) |
| Sıklık | 50/60 Hz |
| Maksimum Akım | 10/16A |
| Koruma Derecesi | IP65 |
| Maksimum Çalışma Basıncı | 10 bar |
| Minimum Çalışma Sıcaklığı | 0 °C |
| Maksimum Çalışma Sıcaklığı | 65 °C |
| Bağlantılar | 1-inch male threads |
| Minimum Intervention Pressure | 1.5 bar |
| Boyutlar (U x Y x D) | 174x221x174 mm |
| Ağırlık | 4.5 kilo |
| Malzeme | Döküm demir |
5. Kurulum
Proper installation is crucial for the safe and efficient operation of the Easy Press-1. It is highly recommended that installation be carried out by a qualified technician.
5.1. Montaj Yeri
- Install the device in a vertical position, ensuring the flow direction arrows on the unit match the water flow.
- Choose a location protected from direct sunlight, frost, and excessive humidity.
- Ünitenin etrafında yeterli havalandırma olduğundan emin olun.
5.2. Hidrolik Bağlantılar
- Connect the inlet of the Easy Press-1 to the pump outlet.
- Connect the outlet of the Easy Press-1 to the water distribution system.
- Use appropriate sealing materials (e.g., PTFE tape) on the 1-inch male threaded connections to prevent leaks.
- Tüm bağlantıların sıkı olduğundan emin olun, ancak aşırı sıkmayın.
5.3. Elektrik Bağlantıları
- UYARI: Herhangi bir elektrik bağlantısı yapmadan önce ana güç kaynağının kesildiğinden emin olun.
- Connect the main power supply (230V, 50/60Hz) to the designated input terminals of the Easy Press-1.
- Connect the single-phase electric pump to the designated output terminals of the Easy Press-1.
- Ensure proper grounding for both the Easy Press-1 and the electric pump.
- Verify all connections are secure and insulated according to electrical standards.
6. Operasyon
6.1. İlk Başlatma
- After completing all hydraulic and electrical connections, ensure the pump is primed (filled with water) if required by the pump manufacturer.
- Open a tap in the system to allow water to flow.
- Restore power to the Easy Press-1. The green POWER indicator should illuminate.
- The pump will start automatically and run until the system is pressurized and the tap is closed.
- Close the tap. The pump should stop after a few seconds.
6.2. Normal Çalışma
The Easy Press-1 operates automatically:
- When a tap is opened, the pressure in the system drops, and the Easy Press-1 starts the pump.
- When the tap is closed, the pressure rises, and the Easy Press-1 stops the pump after a short delay.
6.3. Dry-Run Protection and Automatic Reset
If the pump runs without water (dry running), the Easy Press-1 will detect this condition and stop the pump to prevent damage. The red STATUS indicator will illuminate.
- Otomatik Sıfırlama: The device will attempt to restart the pump periodically (e.g., every 15-30 minutes) to check if water has returned. If water is detected, normal operation resumes.
- Manuel sıfırlama: To manually reset the device after a dry-run event, press the START/STOP button. Ensure the water supply to the pump has been restored before attempting a manual reset.
7. Bakım
The Pedrollo Easy Press-1 is designed for minimal maintenance. However, regular checks can ensure its longevity and optimal performance.
- Görsel Muayene: Periodically inspect the unit for any signs of damage, leaks, or corrosion.
- Temizlik: Cihazın dış yüzeyini temiz tutun ve toz ve kirden arındırın. Yumuşak bir bez kullanın.amp Temizlik için bez kullanın; aşındırıcı temizleyiciler veya çözücüler kullanmayın.
- Bağlantılar: Check hydraulic and electrical connections periodically to ensure they remain tight and secure.
- Kışlama: In areas prone to freezing temperatures, ensure the unit and associated piping are drained or protected from frost to prevent damage.
8. Sorun Giderme
This section provides solutions to common issues you might encounter with your Easy Press-1 controller.
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Musluk açıldığında pompa çalışmıyor. | Güç kaynağı yok. Dry-run protection activated. Hatalı kablolama. | Güç bağlantısını ve devre kesiciyi kontrol edin. Check water supply to pump; press START/STOP button to reset. Verify all electrical connections are secure. Consult a qualified technician. |
| Pompa sürekli çalışıyor. | Sistemde sızıntı. Tap not fully closed. Basınç sensörü arızalı. | Inspect plumbing for leaks and repair. Ensure all taps are completely closed. Teknik destekle iletişime geçin. |
| Pump starts and stops frequently (short cycling). | Sistemde küçük bir sızıntı var. Kontrol vanası sorunu. Yetersiz su temini. | Inspect plumbing for minor leaks and repair. Check the pump's check valve for proper function. Ensure adequate water supply to the pump. |
| Red STATUS indicator is on. | Dry-run protection activated. | Check water supply to the pump. Once water is restored, press the START/STOP button to manually reset, or wait for automatic reset. |
9. Garanti ve Destek
For warranty information, please refer to the documentation provided at the time of purchase or contact your authorized Pedrollo dealer. Keep your proof of purchase for warranty claims.
For technical assistance, spare parts, or service, please contact Pedrollo customer support or an authorized service center. Contact details can typically be found on the manufacturer's official websitenizden veya perakendeciniz aracılığıyla.