Darkglass Microtubes B7K V2 Bas Ön Amplifikatörüamp Pedal Kullanım Kılavuzu

1. Giriş

The Darkglass Microtubes B7K V2 is a versatile bass preamp pedal designed to provide a wide range of tonal options for electric bass players. It combines a powerful overdrive circuit with a comprehensive 4-band equalizer and a balanced XLR output, making it suitable for both live performance and studio recording. This manual provides detailed instructions for setting up, operating, and maintaining your B7K V2 pedal.

2. Özellikler

• Combines a preamp, EQ, and overdrive in one unit for powerful tone shaping.
• Features a blend control to mix clean and overdriven signals for perfect balance.
• Includes a 4-band active EQ with bass, low mids, high mids, and treble controls.
• Grunt switch adds three levels of low-end boost for a thicker sound.
• Attack switch adjusts treble content, offering boost, flat, and cut settings.
• Low mids switch changes the center frequency from 1 kHz to 500 Hz.
• Hi mids switch changes the center frequency from 3 kHz to 1.5 kHz.
• Parallel output for running the input signal through unaffected.
• Direct output provides a balanced version for PA systems or studio consoles.
• Operates with a regulated 9V DC adapter (not included).

3. Kontroller ve Bağlantılar

Şekil 1: Üst view of the B7K V2 pedal.

Figure 2: Left side connections.

Figure 3: Right side connections.

3.1 Kontrol Düğmesi

• karışım: Mixes the clean input signal with the overdriven signal. The clean signal remains at unity gain while the volume of the overdriven signal is controlled by the Drive knob, allowing for fine-tuning of the blend ratio.
• Seviye: Pedalların toplam çıkış ses seviyesini ayarlar.
• Sürmek: Controls the amount of gain in the overdriven signal.
• Düşük: Adjusts the level of the low frequencies.
• Lo Mid'ler: Adjusts the level of the low-mid frequencies. The center frequency can be switched between 500 Hz and 1 kHz.
• Merhaba Midler: Adjusts the level of the high-mid frequencies. The center frequency can be switched between 1.5 kHz and 3 kHz.
• tiz: Adjusts the level of the high frequencies.

3.2 Anahtarları

• Saldırı Anahtarı: Modifies the treble content of the overdriven signal. Options are Boost, Flat, and Cut.
• Grunt Anahtarı: Modifies the low-end content of the overdriven signal. Options are Thin, Raw, and Fat.
• Lo Mids Switch: Selects the center frequency for the Lo Mids knob (500 Hz or 1 kHz).
• Merhaba Mid Anahtarı: Selects the center frequency for the Hi Mids knob (1.5 kHz or 3 kHz).
• Zemin Kaldırma Anahtarı: Disconnects the ground from the XLR output to help eliminate hum or ground loops when connected to external equipment.

3.3 Bağlantılar

• Input (1/4" Jack): Connect your bass guitar or other instrument here.
• Output (1/4" Jack): Connect to your bass amplifier veya diğer efekt pedalları.
• Direct Output (XLR): Provides a balanced output for connecting directly to a PA system, mixing console, or audio interface.
• Parallel Output (1/4" Jack): Outputs the unaffected input signal, useful for parallel processing or sending a clean signal to another device.
• 9VDC Girişi: Connect a regulated 9V DC power supply (center negative, minimum 30mA).

4. Kurulum

1. Ensure the pedal is powered off before making any connections.
2. Bas gitarınızı şuraya bağlayın: Giriş Pedalların sağ tarafında jak girişi bulunmaktadır.
3. Bağlan Çıktı jack on the left side to your bass amplifier'in girdisi.
4. If using the balanced output, connect the Direct Output (XLR) to a PA system, mixing console, or audio interface.
5. If you need an unaffected signal, connect the Paralel Çıkış başka bir cihaza.
6. Connect a regulated 9V DC (center negative) power supply to the 9VDC Girişi. The pedal requires a minimum of 30mA. Note: A power supply is not included with the pedal.
7. Once all connections are secure, you can power on the pedal.

5. Kullanım Talimatları

5.1 Temel İşlemler

To activate the pedal, press the footswitch. The LED indicator will illuminate. To bypass the effect, press the footswitch again.

5.2 Ton Şekillendirme

• Start with all EQ knobs (Low, Lo Mids, Hi Mids, Treble) at the 12 o'clock position for a flat response.
• Ayarla Sürmek knob to achieve your desired level of overdrive. Higher settings will produce more distortion.
• Kullanın Karışım knob to mix the clean signal with the overdriven signal. This allows you to retain clarity and low-end presence while adding grit.
• Deney yapın Saldırı Ve Homurdanma switches to fine-tune the treble and bass characteristics of the overdriven tone.
• Utilize the 4-band EQ to sculpt your overall tone. The Lo Mids Ve Merhaba Mid'ler switches allow you to select different frequency centers for precise control.
• Ayarla Seviye knob to match the output volume with your bypassed signal or to boost your signal for solos.

6. Bakım

• Pedal yüzeyini yumuşak, kuru bir bezle silerek temiz tutun. Aşındırıcı temizleyiciler veya çözücüler kullanmaktan kaçının.
• Protect the pedal from extreme temperatures, moisture, and direct sunlight.
• Sinyal kaybını veya hasarı önlemek için tüm kabloların iyi durumda ve doğru şekilde bağlı olduğundan emin olun.
• Always use a regulated 9V DC center-negative power supply to avoid damage to the unit.

7. Sorun Giderme

8. Özellikler

• Ürün Ağırlığı: 1.1 pound (0.5 Kilogram)
• Ürün Ölçüleri: 6 x 7 x 10 inç
• Ürün Model Numarası: B7K2
• Renk: Siyah
• Bağlantı Tipi: 1/4" (aux), XLR
• Donanım Arayüzü: USB (for potential future firmware updates, not for audio)
• Sinyal Formatı: Analog
• Güç Kaynağı: Kablolu Elektrik
• Cilttage: 9 Volts DC (center negative)
• Güncel Çekiliş: En az 30mA

9. Garanti ve Destek

Darkglass Electronics products are designed for reliability and performance. For specific warranty information and support, please refer to the documentation included with your purchase or visit the official Darkglass Electronics webSite. Satın alma belgenizi garanti talepleriniz için saklayın.

For technical assistance or service inquiries, please contact Darkglass Electronics customer support through their official channels.