ZTW TY15124544

ZTW Mantis Slim 15A Brushless ESC Instruction Manual

Model: TY15124544

1. Giriş

The ZTW Mantis Slim 15A Brushless Electronic Speed Controller (ESC) is designed for F3P airplanes and gliders, offering super smooth startup and throttle response. This manual provides essential information for safe and efficient operation of your ESC. Please read it thoroughly before use.

2. Temel Özellikler

3. Özellikler

ÖzellikDeğer
ESC Size (LxWxH)27mm x 14mm x 5.5mm
Giriş Gücü2-4S Lipo / 5-12NC
BEC Çıkışı2A/5V (3A peak)
Sürekli Akım15A
Ağırlık6.8 gr
Motor Konektörü2.0mm female bullet connector
Güç BağlantısıJST (female case with male pin)

Product Dimensions: 1.2 x 1 x 0.1 inches. Item Weight: 0.64 ounces.

ZTW Mantis Slim 15A ESC with detailed dimensions

Figure 1: ZTW Mantis Slim 15A ESC with detailed dimensions (Length: 27mm, Width: 14mm, Height: 5.5mm).

4. Kurulum ve Yükleme

Proper installation is crucial for the performance and safety of your ESC. Follow these steps carefully:

4.1 Kablo Bağlantıları

ZTW Mantis Slim 15A ESC with labeled 2.0mm female bullet motor connectors and JST female power connector

Figure 2: ZTW Mantis Slim 15A ESC showing 2.0mm female bullet motor connectors and JST female power connector.

4.2 ESC'nin Montajı

Choose a location that has good airflow to offer best cooling to prevent overheating. Do NOT cover the side with the flat heat shield with hook and loop tape or any other material as this will greatly lower its effectiveness. Mount the ESC with a combination of hook and loop tape or 2-sided foam tape.

Video 1: Brushless ESC for Drone & RC Plane Easy to install (Source: HAWK'S WORK). This video demonstrates the general installation process of a Brushless ESC for a Drone or RC Plane, highlighting easy installation steps.

5. Kullanım Talimatları

Always perform throttle calibration before the first use or if you change your transmitter.

5.1 Gaz Kalibrasyonu

  1. Telsizinizi açın ve gaz kolunu en üst konumda tutun.
  2. Connect the battery pack to the ESC. Wait for about 2 seconds, the motor will beep twice, then pull the throttle to the minimum position. The motor will also beep, which indicates that your ESC has got the signal range of the throttle from your transmitter.

Video 2: How to do throttle calibration for Mantis Slim G2 20A/30A (Source: ZTW Model). This video provides instructions on how to perform throttle calibration for the Mantis Slim G2 20A/30A ESC, which is applicable to the 15A model.

Video 3: How to calibrate ESC (Source: HAWK'S WORK). This video demonstrates the general process of calibrating an ESC, which can be helpful for understanding the throttle calibration process.

5.2 Programming the ESC

The ZTW Mantis Slim ESC can be programmed using a ZTW Beatles series programming card or directly via your transmitter.

5.2.1 Using an LCD Program Card

  1. Unplug the ESC throttle cable from the receiver.
  2. Insert the LCD Program Card G2 into the ESC's throttle cable port.
  3. ESC'yi bataryaya bağlayın.
  4. Wait for the LCD screen to display the power-on interface.
  5. Press the "ITEM" or "OK" button to enter the parameter setting interface.
  6. Use the navigation buttons to select parameters and adjust values.
  7. Upon completion of programming, press the "OK" button to save the parameters.

Video 4: How to set parameter for Mantis Slim G2 20A/30A by LCD Card (Source: ZTW Model). This video demonstrates how to set parameters for Mantis Slim G2 20A/30A using an LCD Card, which is applicable to the 15A model.

5.2.2 Setting SMR (Switch Motor Rotation) Function

The SMR function allows you to change the motor rotation direction. It is only allowed to be used when the aircraft is landing on the ground, and it can effectively shorten the landing distance of the aircraft.

Video 5: Set the SMR (Reverse) function of your ESC (Source: TOYTENSI). This video explains how to set the SMR (Switch Motor Rotation) function for your ESC, which is useful for controlling motor direction during landing.

6. Bakım

To ensure the longevity and optimal performance of your ZTW Mantis Slim ESC, follow these maintenance guidelines:

7. Sorun Giderme

If you encounter issues with your ESC, consider the following common troubleshooting steps:

8. Güvenlik Bilgileri

Always prioritize safety when operating RC equipment. Failure to do so may result in property damage, injury, or death.

9. Garanti ve Destek

ZTW and HAWK HOBBY offer a 100% free warranty for this ESC. For any issues or support needs, please contact your retailer or the manufacturer directly.

İlgili Belgeler - TY15124544

Önview ZTW Mantis Slim G2 15A ESC Kullanım Kılavuzu
ZTW Mantis Slim G2 15A ESC kullanım kılavuzunda, RC uçaklar için özellikler, teknik özellikler, kurulum, programlama ve sorun giderme ayrıntıları yer almaktadır. Optimum performans için ESC'nizi nasıl kalibre edeceğinizi, programlayacağınızı ve bakımını nasıl yapacağınızı öğrenin.
Önview ZTW Mantis Slim G2 Serisi ESC Kullanım Kılavuzu
ZTW Mantis Slim G2 Serisi Fırçasız Elektronik Hız Kontrol Cihazı (ESC) için RC uygulamalarına yönelik özellikleri, teknik özellikleri, kurulumu, programlamayı ve sorun gidermeyi ayrıntılı olarak açıklayan kullanıcı kılavuzu.
Önview ZTW SkyHawk Serisi ESC Kullanıcı Kılavuzu
ZTW SkyHawk serisi fırçasız elektronik hız kontrol cihazlarının (ESC) kullanım kılavuzu, RC uçaklar ve helikopterler için özellikleri, teknik özellikleri ve sorun gidermeyi ayrıntılı olarak açıklamaktadır.
Önview ZTW Beast Pro 30A G2 BLE Fırçasız ESC Kullanım Kılavuzu
ZTW Beast Pro 30A G2 BLE ESC için 1:28 RC arabalar için özellikleri, teknik özellikleri, kalibrasyonu, uygulama kullanımını ve programlanabilir ayarları kapsayan kullanıcı kılavuzu.
Önview ZTW Fırçasız ESC Program Kartı Talimatları
ZTW Fırçasız ESC Program Kartını kullanarak ZTW'nin Fırçasız Elektronik Hız Kontrol Cihazı parametrelerini ayarlama talimatları. Dahili BEC'li ve BEC'siz ESC'lerle kullanımı kapsar.
Önview ZTW Beast Pro 120A, 160A, 220A Brushless ESC User Manual
User manual for ZTW Beast Pro series brushless electronic speed controllers (ESC) models 120A, 160A, and 220A. This guide details features, specifications, setup, calibration, and advanced programming options for 1:10 & 1:12 scale RC cars and trucks, enhancing performance and driveability.