Rega Planar 2 Pikap Kullanım Kılavuzu

giriiş

Thank you for choosing the Rega Planar 2 Turntable. This manual provides essential information for setting up, operating, and maintaining your new turntable to ensure optimal performance and longevity. The Planar 2 is designed to deliver high-fidelity audio reproduction from your vinyl collection, featuring a new RB220 tonearm, a glass platter, and a pre-installed Carbon cartridge.

Önemli Güvenlik Bilgileri

Please read all safety instructions before operating the turntable. Keep this manual for future reference.

• Üniteyi yağmura veya neme maruz bırakmayın.
• Cihazı sökmeyin. Tüm servis işlemlerini yetkili personele yaptırın.
• Ensure the turntable is placed on a stable, level surface away from direct sunlight, heat sources, and excessive vibration.
• Disconnect the power cord from the wall outlet if the unit will not be used for a long period.
• Avoid touching the stylus (needle) directly.

Paket İçeriği

Lütfen kutuda tüm ürünlerin mevcut olduğundan emin olun:

• Rega Planar 2 Turntable Plinth with pre-installed RB220 Tonearm and Carbon Cartridge
• Glass Platter (Optiwhite 10mm)
• Keçe Mat
• Drive Belt (pre-installed)
• Karşı ağırlık
• Toz Kapağı
• Güç Kaynağı
• Kullanım Kılavuzu (bu belge)

Kurulum Kılavuzu

Follow these steps to set up your Rega Planar 2 Turntable:

1. Yerleşim

Place the turntable plinth on a firm, level surface, ideally on a dedicated audio rack or a sturdy shelf. Ensure there is adequate space around the unit for ventilation and operation.

Figure 1: Rega Planar 2 Turntable with dust cover and glass platter.

2. Platter Installation

1. Carefully place the 10mm Optiwhite glass platter onto the sub-platter spindle. Ensure it sits flush and rotates freely.
2. Keçe altlığı cam tabağın üzerine yerleştirin.

Figure 2: Rega Planar 2 Turntable with felt mat installed on the glass platter.

3. Tonearm and Cartridge Setup (RB220 Tonearm with Carbon Cartridge)

The RB220 tonearm features an automatic bias setting, simplifying setup. The Carbon cartridge is pre-installed.

1. Remove the stylus guard from the Carbon cartridge.
2. Slide the counterweight onto the rear stub of the tonearm.
3. Adjust the counterweight until the tonearm floats freely and is perfectly balanced horizontally. This is the zero-tracking force position.
4. Once balanced, carefully push the counterweight inwards towards the pivot until it aligns with the recommended tracking force for the Carbon cartridge (typically 2g). The RB220's automatic bias will compensate for this setting.

Şekil 3: Yakın çekim view of the RB220 tonearm and Carbon cartridge.

4. Birine bağlanma Ampkaldırıcı/Ön-ampcankurtaran

The Rega Planar 2 does not have a built-in phono pre-amplifier. You will need an external phono stage or an amplifier with a dedicated "Phono" input.

1. Connect the RCA cables from the turntable to the "Phono" input on your amplifier or external phono pre-ampcankurtaran.
2. Connect the ground wire (if present) from the turntable to the ground terminal on your amplifier or phono pre-ampcankurtaran.
3. Connect the power supply to the turntable and then plug it into a wall outlet.

Kullanım Talimatları

1. Açma/Kapama

Locate the power switch on the underside of the plinth, typically on the left front corner. Flip the switch to turn the turntable on or off. The platter will begin to spin when powered on.

2. Plak Çalma

1. Place a record on the felt mat, ensuring it is centered on the spindle.
2. Unlock the tonearm from its rest.
3. Kaldırma kolunu kullanarak pikap kolunu yavaşça yukarı kaldırın.
4. Pikap kolunu, plağın istenen başlangıç ​​oluğunun üzerine dikkatlice yerleştirin.
5. İğnenin plağın üzerine inmesini sağlamak için kolu yavaşça aşağı indirin.
6. At the end of the record, lift the tonearm using the cueing lever and return it to its rest, securing it in place.

3. Changing Playback Speed (33 1/3 RPM to 45 RPM)

The Rega Planar 2 requires manual speed change:

1. Turn off the turntable power.
2. Carefully remove the glass platter and felt mat.
3. Locate the drive belt around the motor pulley and sub-platter.
4. To change from 33 1/3 RPM to 45 RPM, move the drive belt to the larger diameter groove on the motor pulley.
5. To change from 45 RPM to 33 1/3 RPM, move the drive belt to the smaller diameter groove on the motor pulley.
6. Replace the glass platter and felt mat.
7. Turn on the turntable power.

Şekil 4: View of the sub-platter and drive belt mechanism for speed adjustment.

4. Dust Cover Usage

The included dust cover protects the turntable from dust and debris. It can be lifted and removed if desired during playback or setup. Ensure the dust cover is closed when the turntable is not in use.

Bakım

• Cleaning the Plinth and Dust Cover: Use a soft, dry, lint-free cloth to wipe the plinth and dust cover. For stubborn marks, a slightly damp Önce bir bez kullanılabilir, ardından kuru bir bezle silin. Aşındırıcı temizleyicilerden veya çözücülerden kaçının.
• Kalemin Temizlenmesi: Periodically clean the stylus using a soft brush designed for stylus cleaning, brushing gently from back to front.
• Tahrik Kayışı: The drive belt should be inspected periodically for wear. If it appears stretched or cracked, it may need replacement to maintain accurate speed.
• Kartuş Değiştirme: The Carbon cartridge has a finite lifespan. When sound quality degrades or distortion increases, it may be time to replace the cartridge. Consult a qualified dealer for replacement and installation.

Sorun giderme

Özellikler

Garanti ve Destek

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official REGA webSite. Satın alma belgenizi garanti talepleriniz için saklayın.

For further assistance, you may contact your authorized REGA dealer.