1. Giriş
This manual provides detailed instructions for the installation, operation, and maintenance of the CDVI 433MHz Radio Keypad (Digicode) and its associated SEL2641R433NN 1-Relay 12V Receiver. This system is designed for secure access control applications.
Lütfen kurulum veya çalıştırma işlemlerine başlamadan önce, işlevselliğin doğru şekilde çalışması ve güvenliğin sağlanması için bu kılavuzu dikkatlice okuyun.
Figure 1: CDVI 433MHz Radio Keypad and SEL2641R433NN Receiver. The image shows the silver-colored keypad with illuminated blue numbers (0-9, A, B, C) and a transparent plastic receiver unit.
2. Güvenlik Bilgileri
- Kurulum veya bakım işlemlerinden önce tüm elektrik bağlantısının kesildiğinden emin olun.
- Kurulum yalnızca kalifiye personel tarafından yapılmalıdır.
- Do not expose the keypad or receiver to extreme temperatures, moisture, or direct sunlight.
- Use only specified power supply (12V).
- Çocukların erişemeyeceği yerde saklayınız.
3. Kurulum ve Kurulum
3.1. Bileşenler Bittiview
Sistem iki ana bileşenden oluşmaktadır:
- Radio Keypad (Digicode): The input device for entering access codes.
- SEL2641R433NN Receiver: The unit that receives signals from the keypad and controls the access mechanism (e.g., door lock).
3.2. Tuş Takımının Montajı
- Choose a suitable mounting location, typically near the access point, ensuring it is protected from direct weather exposure if outdoors.
- Mark the drilling points using the keypad's mounting plate as a template.
- Delikler açın ve uygun dübelleri takın.
- Montaj plakasını duvara sabitleyin.
- Attach the keypad securely to the mounting plate.
3.3. Alıcının Kablolaması
The SEL2641R433NN receiver requires a 12V power supply and connection to the access control device. Refer to the wiring diagram below for typical connections.
- Güç Girişi: Connect 12V DC to the designated terminals. Observe polarity.
- Röle Çıkışı: The receiver has one relay. Connect the Normally Open (NO) or Normally Closed (NC) contacts to your access control device (e.g., electric strike, magnetic lock) as required.
(Note: A detailed wiring diagram is typically provided with the physical product. Consult it for specific terminal assignments.)
4. Kullanım Talimatları
4.1. İlk Güçlendirme
Once the receiver is wired and powered, it will enter a standby mode. The keypad will illuminate when a button is pressed.
4.2. Programming Access Codes
The keypad and receiver must be paired, and access codes programmed. This process typically involves:
- Programlama Moduna Giriş: This usually involves a master code or a physical button on the receiver.
- Adding New Codes: Follow the specific sequence to input new user codes (e.g., Master Code + * + New Code + #).
- Deleting Codes: Follow the specific sequence to remove existing user codes.
- Programlama Modundan Çıkış: Save changes and exit programming mode.
(Note: Refer to the specific programming instructions provided with your product for exact key sequences and procedures, as these can vary by firmware version.)
4.3. Erişim İzni Verme
To grant access, simply enter a valid programmed code on the keypad. Upon successful code entry, the receiver's relay will activate for a pre-set duration, unlocking the connected device.
5. Bakım
- Temizlik: Tuş takımının yüzeyini yumuşak bir bezle temizleyin.amp bezle silin. Aşındırıcı temizleyiciler veya çözücüler kullanmayın.
- Düzenli Kontroller: Periodically check all wiring connections for security and integrity, especially for the receiver unit.
- Kod Yönetimi: Düzenli olarak tekrarview and update access codes for security purposes. Delete codes of former users.
6. Sorun Giderme
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Tuş takımı yanıt vermiyor. | No power to receiver or keypad not paired. | Check 12V power supply to receiver. Ensure keypad is correctly paired with the receiver. |
| Access code not working. | Incorrect code entered, code not programmed, or keypad/receiver not paired. | Verify code. Re-program code. Re-pair keypad and receiver. |
| Door/lock not activating. | Incorrect wiring to lock, faulty lock, or relay issue. | Check wiring connections. Test the lock mechanism independently. Consult a technician if relay is suspected faulty. |
| Short range or intermittent operation. | Radio interference or receiver antenna issue. | Check for sources of radio interference. Ensure receiver antenna is unobstructed. |
7. Özellikler
| Özellik | Detay |
|---|---|
| Model Numaraları | SEL2641R433NN, GALEOR1R, F1002000052 |
| Sıklık | 433MHz |
| Alıcı Güç Kaynağı | 12V doğru akım |
| Röle Çıkışı | 1 Relay (NO/NC contacts) |
| Tuş takımı türü | Radio (Wireless) |
| ASIN | B06VWH6V57 |
8. Garanti ve Destek
Information regarding product warranty is typically provided with the purchase documentation or can be found on the manufacturer's official webLütfen garanti talepleriniz için satın alma belgenizi saklayın.
For technical support or further assistance, please contact CDVI customer service or your authorized dealer. Contact details can usually be found on the CDVI webalan (www.cdvi.com).