1. Giriş
This manual provides essential instructions for the proper installation, operation, and maintenance of the Protech 61-104025-15 Service Valve. Adhering to these guidelines will ensure safe and efficient performance of the valve. Please read this manual thoroughly before proceeding with any procedures.
2. Ürün Bittiview
The Protech 61-104025-15 Service Valve is a component designed for various industrial and plumbing applications, particularly within HVAC and refrigeration systems. It facilitates isolation and control of fluid flow, allowing for system servicing without complete depressurization or drainage. This valve is compatible with models such as raka, rakb, ralc, rama, ramb, ramc, ramm, ranc, rand, ranl, rapa, rapb, rapc, rapl, rapm, rara, rarl, rasl, rpka, rpkb, rpla, rplb, rpmb, rpmc, rpmd, rpmm, rpne, rpnk, rpnl, rppb, rppc, rppl, rpql, rprl, saka, sakb, spkb.
Şekil 1: The Protech 61-104025-15 Service Valve. This image displays the brass-colored valve body, featuring two 3/4-inch sweat ODF connections on opposing sides and a hexagonal cap at the top for manual operation.
3. Kurulum ve Kurulum
Installation of the Protech 61-104025-15 Service Valve requires careful attention to connection types and proper sealing techniques. It is recommended that installation be performed by a qualified technician.
3.1 Bağlantı Ayrıntıları
- Upper Connection Size: 3/4 inç
- Upper Connection Type: Sweat ODF (Outer Diameter Flare)
- Lower Connection Size: 3/4 inç
- Lower Connection Type: Sweat ODF (Outer Diameter Flare)
3.2 Kurulum Prosedürü
- Önce Güvenlik: Kurulum işlemine başlamadan önce sistemin basıncının boşaltıldığından ve suyunun kesildiğinden emin olun. Uygun kişisel koruyucu ekipman (KKD) kullanın.
- Bağlantıları Hazırlayın: Clean the ends of the pipes and the valve's sweat connections thoroughly to remove any dirt, grease, or oxidation. Apply appropriate flux to both surfaces.
- Vanayı konumlandırın: Place the valve in the desired position, ensuring proper alignment with the piping.
- Lehim Bağlantıları: Using a suitable heat source and solder, create strong, leak-free sweat joints. Allow the joints to cool naturally.
- Sızıntı Testi: After installation, pressurize the system and carefully check all connections for leaks using an approved leak detection method.
4. Operasyon
The Protech 61-104025-15 Service Valve is designed for straightforward manual operation to control or isolate fluid flow within a system.
4.1 Vananın Açılması ve Kapatılması
- İle açık the valve, turn the hexagonal cap counter-clockwise until the desired flow is achieved or the valve is fully open.
- İle kapalı the valve, turn the hexagonal cap clockwise until the valve is fully closed and flow is stopped. Do not overtighten.
Always operate the valve smoothly and avoid sudden, forceful movements to prevent damage to the valve or system components.
5. Bakım
Regular maintenance ensures the longevity and reliable performance of your Protech 61-104025-15 Service Valve.
- Periyodik muayene: Visually inspect the valve and its connections regularly for any signs of wear, corrosion, or leaks.
- Temizlik: Keep the exterior of the valve clean. Avoid using harsh chemicals that could damage the valve material.
- Sızıntı Tespiti: Periodically check for leaks around the valve body and connections, especially after any system pressure changes.
- Operasyonel Kontrol: Cycle the valve (open and close) periodically to ensure smooth operation and prevent seizing, particularly in systems where the valve remains in one position for extended periods.
6. Sorun Giderme
This section addresses common issues that may arise with the service valve.
6.1 Yaygın Sorunlar ve Çözümler
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Bağlantı noktalarında sızıntı | Improper soldering; damaged pipe or valve connection | Depressurize system, repair or re-solder connection. Replace valve or pipe if damaged. |
| Valfi çevirmek zor. | Internal corrosion or debris; lack of lubrication | Do not force. Depressurize system and inspect. If internal, valve replacement may be necessary. |
| No flow or restricted flow when open | Valve not fully open; internal obstruction | Ensure valve is fully open. Depressurize system and inspect for internal debris. |
Listede yer almayan sorunlar için veya çözümler sorunu gidermezse, yetkili bir servis teknisyenine başvurun.
7. Özellikler
| Şartname | Detay |
|---|---|
| Marka | ProTech |
| Model Numarası | 61-104025-15 |
| Upper Connection Size | 3/4 inç |
| Upper Connection Type | Sweat ODF |
| Lower Connection Size | 3/4 inç |
| Lower Connection Type | Sweat ODF |
| Dış Cephe Kaplama | Paslanmaz çelik |
| Port Sayısı | 2 |
| Şartname Karşılandı | ASME B16.34 |
| Ürün Ağırlığı | 11.2 ons |
| Ürün Boyutları (U x G x Y) | 3.8 x 3.2 x 4.3 inç |
| UPC | 662766520378 |
8. Garanti Bilgileri
Unless otherwise noted, all Protech items carry a one-year limited warranty from the date of purchase. Please retain your proof of purchase for warranty claims.
9. Destek
For technical assistance, replacement parts, or further inquiries regarding the Protech 61-104025-15 Service Valve, please contact a qualified HVAC or plumbing professional. For general product information, you may visit the Amazon'da ProTech Mağazası.
