Viltrox JY-610C Mini Flash Light User Manual

1. Giriş

The Viltrox JY-610C is a compact and lightweight mini speedlite designed for Canon DSLR cameras. It supports E-TTL, Manual (M), and Multi (Stroboscopic) flash modes, offering versatile lighting control. This manual provides detailed instructions for the proper setup, operation, and maintenance of your JY-610C flash unit.

2. Güvenlik Bilgileri

• Do not disassemble or attempt to repair the unit yourself. Refer to qualified service personnel.
• Keep the unit dry. Do not expose it to rain or moisture.
• Yalnızca belirtilen AA pilleri kullanın. Eski ve yeni pilleri veya farklı pil türlerini karıştırmayın.
• Avoid direct eye exposure to the flash light, especially at close range, as it can cause temporary vision impairment.
• Çocukların erişemeyeceği yerde saklayınız.

3. Paket İçeriği

Paketin içinde tüm öğelerin mevcut olduğundan emin olun:

• Viltrox JY-610C Mini Speedlite
• Taşıma Çantası
• User Manual (English and Chinese)

Note: AA batteries are not included and must be purchased separately.

4. Ürün Bittiview

Familiarize yourself with the components and controls of the Viltrox JY-610C Mini Flash Light.

Şekil 4.1: Ön View
This image shows the front of the Viltrox JY-610C flash unit, highlighting the LCD display, control buttons (Pilot, Mode, T/CH/D, Hz/GR, ON/OFF), and the hot shoe mount with its locking mechanism.

Şekil 4.2: Üst View
En üst view of the Viltrox JY-610C, displaying the "SPEEDLITE JY610C" branding and the flash head. This perspective shows the compact design of the unit.

Şekil 4.3: Yan View with Battery Compartment Open
This image illustrates the side of the flash unit with the battery compartment door open, revealing the slots for AA batteries. This is where batteries are inserted or replaced.

Şekil 4.4: Arka View
Arka taraf view of the Viltrox JY-610C, showing the hot shoe connection point for mounting on a camera, the slave sensor (red window), and regulatory markings. The locking ring for secure attachment is also visible.

Figure 4.5: LCD Display Modes
This composite image shows the Viltrox JY-610C flash unit alongside close-ups of its LCD screen displaying different operational modes: Manual (M) with power setting, Multi (Stroboscopic) with frequency and flash count, and E-TTL with exposure compensation. This demonstrates the user interface for mode selection and settings adjustment.

4.1. Kontrol Paneli

• LCD Ekran: Geçerli ayarları ve modu görüntüler.
• AÇIK/KAPALI Düğmesi: Üniteyi açar veya kapatır.
• MOD Düğmesi: Cycles through E-TTL, M (Manual), and Multi (Stroboscopic) flash modes.
• T/CH/D Button: Used for setting channels/groups in slave mode or other parameters.
• Hz/GR Button: Used for setting frequency in Multi mode or groups.
• PILOT Button: Test flash button. Also serves as a flash-ready indicator (red light).
• Yön Tuşları (Yukarı/Aşağı/Sol/Sağ): Menülerde gezinin ve ayarları düzenleyin.
• Ayarlama düğmesi: Seçimleri onaylar.

5. Kurulum

5.1. Pil Kurulumu

1. Open the battery compartment cover located on the side of the flash unit (refer to Figure 4.3).
2. Insert two (2) AA-size batteries according to the polarity indicators inside the compartment.
3. Pil bölmesi kapağını sıkıca kapatın.

Note: Ensure batteries are inserted correctly to prevent damage to the unit.

5.2. Kameraya Montaj

1. Slide the hot shoe mount of the JY-610C into the hot shoe of your Canon DSLR camera.
2. Rotate the locking ring clockwise until the flash unit is securely fastened to the camera's hot shoe. Do not overtighten.
3. To remove, rotate the locking ring counter-clockwise and slide the flash unit off the hot shoe.

6. Çalışma Modları

Basın MOD button to cycle through the available flash modes: E-TTL, M (Manual), and Multi (Stroboscopic).

6.1. E-TTL Mode (Automatic Flash)

In E-TTL mode, the flash output is automatically controlled by the camera to achieve optimal exposure. This mode is ideal for general photography.

• Basmak MOD until "E-TTL" appears on the LCD screen (refer to Figure 4.5).
• You can adjust Flash Exposure Compensation (FEC) using the directional buttons (e.g., +1/3, +2/3, etc.) if needed. Press AYARLAMAK onaylamak için.
• The flash will fire automatically based on the camera's metering.

6.2. Manuel (M) Modu

Manual mode allows you to set the flash output power manually, providing precise control over lighting.

• Basmak MOD until "M" appears on the LCD screen (refer to Figure 4.5).
• Use the directional buttons to adjust the flash output from 1/1 (full power) to 1/128, with 22 levels of fine tuning.
• Basmak AYARLAMAK to confirm the power setting.

6.3. Multi (Stroboscopic) Mode

Multi mode fires the flash multiple times during a single exposure, creating stroboscopic effects for capturing motion.

• Basmak MOD until "Multi" appears on the LCD screen (refer to Figure 4.5).
• Use the directional buttons to set the flash frequency (Hz) and the number of flashes.
• Basmak AYARLAMAK onaylamak için.

6.4. Slave Modes (S1/S2)

The JY-610C can function as an optical slave unit, triggered by another flash.

• S1 Modu: The flash will fire in response to the first flash it detects. Suitable for manual flash triggers.
• S2 Modu: The flash will ignore the pre-flash from a master E-TTL flash and fire on the main flash. Suitable for E-TTL master flashes.
• To activate slave mode, press and hold the T/CH/D button until "SLAVE" appears, then use directional buttons to select S1 or S2.
• The unit supports 4 channels in 3 groups for more complex multi-flash setups.

7. Gelişmiş Özellikler

7.1. Exposure Compensation

In E-TTL mode, you can adjust the flash exposure compensation to fine-tune the brightness of your subject. Use the directional buttons to increase or decrease the exposure value.

7.2. Front-Curtain Sync / Rear-Curtain Sync

The JY-610C supports both front-curtain and rear-curtain sync. This setting is typically controlled via your camera's flash menu. Consult your camera's manual for specific instructions on how to enable these features.

• Ön Perde Senkronizasyonu: The flash fires immediately after the shutter opens.
• Arka Perde Senkronizasyonu: The flash fires just before the shutter closes. Useful for creating motion blur effects with the flash freezing the subject at the end of the exposure.

7.3. Adjustable Vertical Angle

The flash head can be tilted vertically to angles of 60, 75, and 90 degrees. This allows for bounce flash photography, directing the light off a ceiling or wall for softer, more natural illumination.

8. Bakım

• Temizlik: Flaş ünitesini temizlemek için yumuşak, kuru bir bez kullanın. İnatçı kirler için, biraz daha yumuşak bir bez yeterli olacaktır.amp Önce bir bez, ardından kuru bir bez kullanılabilir. Güçlü deterjanlar veya çözücüler kullanmayın.
• Depolamak: When not in use for extended periods, remove the batteries to prevent leakage and store the unit in its carrying bag in a cool, dry place.
• Pil Bakım: Replace batteries when the recycle time becomes excessively long or the flash-ready indicator does not light up.

9. Sorun Giderme

10. Özellikler

11. Garanti ve Destek

For warranty information and technical support, please refer to the warranty card included with your product or visit the official Viltrox webSite. Satın alma fişinizi, garanti talepleriniz için satın alma belgeniz olarak saklayın.