1. Giriş
This manual provides essential information for the MOOG 513346 Wheel Bearing and Hub Assembly. This component is engineered to deliver reliable performance and facilitate straightforward installation in compatible Ford Mustang vehicles. It features an advanced raceway design for extended service life and coated wheel studs for rust protection.
Şekil 1: Ön view of the MOOG 513346 Wheel Bearing and Hub Assembly.
Şekil 2: Arka view of the MOOG 513346 Wheel Bearing and Hub Assembly.
2. Uyumluluk
The MOOG 513346 Wheel Bearing and Hub Assembly is compatible with the following Ford Mustang models:
- 2015-2015 Ford Mustang
- 2016-2020 Ford Mustang
- 2016-2017 Ford Mustang
- 2021-2021 Ford Mustang
Önemli: Satın almadan önceasing and installing, verify compatibility with your specific vehicle by checking the manufacturer's fitment guide or consulting a qualified automotive professional.
3. Güvenlik Bilgileri
Automotive repair can be hazardous. Always prioritize safety. It is recommended that installation be performed by a certified mechanic or an individual with appropriate automotive repair experience.
- Güvenlik gözlüğü ve eldiven gibi uygun kişisel koruyucu ekipman kullanın.
- Herhangi bir çalışmaya başlamadan önce aracın kriko ayakları üzerinde güvenli bir şekilde desteklendiğinden emin olun. Asla yalnızca krikoya güvenmeyin.
- Kurulum işleminin her aşamasında doğru aletleri kullanın.
- Ayrıntılı talimatlar ve tork özellikleri için aracınızın özel servis kılavuzuna bakın.
- Çocukları ve evcil hayvanları çalışma alanından uzak tutun.
4. Dahil Edilen Bileşenler
Her paket şunları içerir:
- One (1) MOOG 513346 Wheel Bearing and Hub Assembly
Figure 3: Key components of the MOOG Wheel Bearing and Hub Assembly.
5. Kurulum Yönergeleri
The MOOG 513346 Wheel Bearing and Hub Assembly is designed for fast and hassle-free installation. However, specific steps may vary depending on your vehicle's configuration. Always consult your vehicle's factory service manual for detailed, model-specific instructions.
Genel Kurulum Adımları (Ayrıntılar için Araç Servis Kılavuzuna Bakınız):
- Aracı güvenli bir şekilde kaldırın ve destekleyin. Tekerleği çıkarın.
- Remove the brake caliper and rotor.
- Disconnect any ABS sensor wiring if present.
- Remove the axle nut. A 35mm socket and a large breaker bar are typically required for this step.
- Remove the bolts securing the old hub assembly to the steering knuckle.
- Carefully remove the old hub assembly.
- Clean the mounting surface on the steering knuckle.
- Install the new MOOG hub assembly, ensuring proper alignment. The coated wheel studs inhibit rust for easier removal and proper torqueing.
- Tighten the hub assembly bolts to the manufacturer's specified torque.
- Install the new axle nut and tighten to the manufacturer's specified torque. A torque wrench capable of 250 ft-lb is often needed for the axle nut.
- Reconnect the ABS sensor wiring.
- Reinstall the brake rotor and caliper.
- Tekerleği tekrar takın ve aracı indirin.
Figure 4: Illustration of wheel installation, highlighting the ease of assembly.
6. Çalışma Özellikleri
Once installed, the MOOG 513346 Wheel Bearing and Hub Assembly contributes to the safe and smooth operation of your vehicle's wheel system. Its application-specific advanced raceway design is engineered to reduce stress, rotation, and heat on components, thereby extending service life and maintaining optimal performance.
Figure 5: Cross-section illustrating the durable raceway design for extended service life.
7. Bakım
Wheel bearing and hub assemblies are critical components that require minimal direct maintenance after proper installation. However, regular inspection during tire rotations or brake service is recommended.
- Denetleme: Periodically check for signs of wear, such as excessive play in the wheel, unusual noises, or visible damage to the hub assembly or its seals.
- Yağlama: This assembly is designed to be maintenance-free with factory-sealed lubrication (grease). No additional lubrication is typically required.
- Korozyon Koruması: The coated wheel studs are designed to resist corrosion, aiding in easier future removal and proper torqueing.
Figure 6: Coated wheel studs for enhanced corrosion protection.
8. Sorun Giderme
If you suspect an issue with your wheel bearing and hub assembly, observe the following common symptoms:
- Alışılmadık Gürültü: A humming, grinding, or growling noise that increases with vehicle speed.
- Titreşim: Vibrations felt through the steering wheel or floorboard, especially at certain speeds.
- ABS Işığı: Illumination of the Anti-lock Braking System (ABS) warning light on the dashboard.
- Direksiyonun Gevşekliği: A feeling of looseness or excessive play in the steering.
If any of these symptoms occur, it is crucial to have your vehicle inspected by a qualified mechanic immediately to prevent further damage or safety risks.
Figure 7: Symptom - Vehicle Noise/Vibration
Figure 8: Symptom - Steering Wheel Vibration
Figure 9: Symptom - ABS Warning Light
9. Özellikler
| Marka | MOOG |
| Model Numarası | 513346 |
| Ürün Boyutları (U x G x Y) | 5.88 x 3.75 x 6 inç |
| Ürün Ağırlığı | 6.64 pound |
| Rulman Numarası | 513346 |
| Rulman Tipi | Bilyalı Rulman |
| Uyumlu Yağlayıcı | Gres |
| UPC | 019826213723 |
| Üretici Parça Numarası | 513346 |
Figure 10: MOOG components undergo rigorous testing for reliability.
10. Garanti Bilgileri
For detailed warranty information regarding the MOOG 513346 Wheel Bearing and Hub Assembly, please refer to the official MOOG website or contact your point of purchase. Warranty terms and conditions may vary.
11. Destek
If you require technical assistance, have questions about installation, or need further support, please contact MOOG customer service or consult a certified automotive technician.
Daha fazla bilgi ve iletişim bilgilerini resmi web sitesinde bulabilirsiniz. MOOG Mağazası.
