Intex Sand Filter Pump Repair Kit

1. Giriş

This manual provides instructions for the Intex Sand Filter Pump Repair Kit, Model 25013. This kit is designed to replace worn or damaged O-rings and the air release valve in compatible Intex sand filter pumps, helping to resolve leaks and maintain efficient pump operation. Proper installation of these components is crucial for the longevity and performance of your pool's filtration system.

2. Güvenlik Bilgileri

• Her zaman gücü kesin to the sand filter pump before performing any maintenance or repair.
• Depressurize the system by opening the air release valve and ensuring all pressure is relieved before opening any part of the pump.
• Eldiven ve göz koruyucu gibi uygun kişisel koruyucu ekipman kullanın.
• Tüm parçaları çocukların erişemeyeceği bir yerde saklayın.
• Refer to your specific Intex sand filter pump's original manual for detailed disassembly and reassembly procedures.

3. Kit İçeriği ve Uyumluluk

The Intex Sand Filter Pump Repair Kit (Model 25013) includes essential replacement parts for various Intex sand filter pumps. This kit is compatible with select Intex sand filter pumps, particularly those requiring part number 25013.

Dahil Bileşenler:

• 1 Tank O-ring (for 12 and 14 inch sand filter pumps and combos, part 11379)
• 1 Drain Valve O-ring (for sand filter pump and combo, part 11385)
• 1 L-shape O-ring (for sand filter pump motor, part 11412)
• Additional assorted O-rings for various pump sections.
• 1 Air Release Valve.

Image: Assortment of black O-rings of various sizes included in the kit.

Image: Two large and two small black O-rings, illustrating different sizes.

Image: A gray plastic air release valve, a key component for pump maintenance.

Image: Three black O-rings of varying sizes, demonstrating the range of seals provided.

4. Kurulum ve Kurulum

Replacing O-rings and the air release valve requires careful attention to detail. Always refer to your specific Intex sand filter pump's instruction manual for exact steps related to its model.

Genel Kurulum Adımları:

1. Güç Bağlantısının Kesilmesi: Ensure the pump is turned off and unplugged from the power source.
2. Sistemin basıncını düşürün: Open the existing air release valve to relieve any pressure within the filter system.
3. Suyu Tahliye Et: If necessary, drain water from the pump and filter tank according to your pump's manual.
4. Sökme: Carefully disassemble the pump components to access the O-rings and air release valve that need replacement. Note the position and orientation of each part.
5. Eski Parçaları Çıkarın: Remove the old, worn, or damaged O-rings and the air release valve. Inspect the surfaces where the new parts will be seated for any debris or damage.
6. Yeni Parçaların Kurulumu: Lightly lubricate new O-rings with a silicone-based lubricant (do not use petroleum-based lubricants as they can degrade rubber) before seating them into their grooves. Install the new air release valve. Ensure all parts are seated correctly and without twists or pinches.
7. Yeniden montaj: Reassemble the pump components, ensuring all connections are secure and tightened appropriately. Do not overtighten.
8. Sızıntı Testi: Once reassembled, slowly turn on the pump and check for any leaks. If leaks occur, turn off the pump, depressurize, and re-check the installation of the O-rings and connections.

5. İşletme Hususları

After successfully replacing the O-rings and air release valve, your Intex sand filter pump should operate without leaks and maintain proper pressure. Monitor the pump's performance for the first few hours of operation to ensure all seals are holding correctly. The air release valve should be used to purge air from the system during initial startup or after any maintenance that exposes the system to air.

6. Bakım

Regular maintenance of your sand filter pump's O-rings and seals is essential for preventing future leaks and ensuring efficient operation.

• Periyodik muayene: Annually, or at the beginning of each pool season, inspect all accessible O-rings for signs of wear, cracking, or flattening. Replace any damaged O-rings promptly.
• Yağlama: Lightly lubricate O-rings with a silicone-based lubricant during reassembly or annual inspection to maintain their flexibility and sealing capability.
• Uygun Depolama: If storing the pump for the off-season, ensure it is clean and dry. Store any spare O-rings in a cool, dry place away from direct sunlight and chemicals.

7. Sorun Giderme

Tamir kitini taktıktan sonra sorunlarla karşılaşırsanız, aşağıdakileri dikkate alın:

• Leaks After Installation:
  • Ensure O-rings are correctly seated in their grooves and not twisted or pinched.
  • Verify that all connections and clamps are tightened securely, but not excessively.
  • Check for any nicks or damage on the O-rings that might have occurred during installation.
• Sistemdeki Hava:
  • Ensure the air release valve is properly installed and closed after purging air.
  • Check all suction side connections for air leaks.
• Low Flow/Pressure:
  • Confirm the pump basket and skimmer basket are clean.
  • Backwash the sand filter if the pressure gauge indicates high pressure.

8. Özellikler

9. Garanti ve Destek

For specific warranty information regarding your Intex Sand Filter Pump Repair Kit or for further technical assistance, please refer to the official Intex website or contact Intex customer support directly. Keep your purchase receipt as proof of purchase.

Intex Customer Support: Lütfen ziyaret edin www.intexcorp.com/support/ İletişim bilgileri ve sıkça sorulan sorular için.