1. Giriş
This manual provides essential information for the safe and correct installation, operation, and maintenance of your Legrand E14 Lamp Holder, model LEG91123. This product is designed for use with E14 screw-base bulbs, with a maximum wattage of 60W and operating at 230 Volts.
2. Güvenlik Bilgileri
WARNING: Risk of electric shock. Always disconnect power at the main circuit breaker before installing or servicing electrical components.
- Kurulum yalnızca yetkili bir elektrikçi veya uzman kişi tarafından yapılmalıdır.
- Herhangi bir işe başlamadan önce güç kaynağının tamamen kapalı olduğundan emin olun.
- Maksimum nominal wat değerini aşmayıntage of 60W for the connected bulb.
- Tüm bağlantıların güvenli ve uygun şekilde yalıtıldığını doğrulayın.
- Bu ürün yalnızca kuru alanlarda iç mekanda kullanılmak üzere tasarlanmıştır.
3. Ürün Bileşenleri
The Legrand E14 Lamp Holder consists of several parts designed for secure and reliable bulb connection.
Figure 3.1: Complete Legrand E14 Lamp Holder. This image shows the complete Legrand E14 lamp holder, featuring the threaded body for bulb insertion and the base for electrical connection.
Figure 3.2: Legrand E14 Lamp Holder disassembled. This image illustrates the main components of the Legrand E14 lamp holder, including the outer casing, internal mechanism, and shade ring.
- Dış Casing: Made of white polyamide material, providing insulation and protection.
- İç Mekanizma: Contains the electrical contacts and wiring terminals.
- Shade Ring: Used to secure a lampl'ye gölgeamp tutucu.
4. Kurulum Talimatları
Follow these steps for proper installation of the Legrand E14 Lamp Tutacak.
- Kablolamayı Hazırlayın: Ensure the power supply is disconnected. Strip approximately 8-10mm of insulation from the ends of the electrical wires.
- Access Terminals: Lamp holder's internal mechanism may need to be partially disassembled to access the wiring terminals. Refer to Figure 3.2 for component identification.
- Kabloları Bağlayın: Insert the stripped wire ends into the designated terminals. The wire entry can be from the side or via a screw connection. Secure the wires firmly by tightening the terminal screws. Ensure no loose strands are present.
Figure 4.1: Internal wiring terminals. This image displays the internal wiring terminals of the Legrand E14 lamp holder, where electrical wires are connected.
- Yeniden birleştirme: Carefully reassemble the lamp holder components, ensuring all parts are correctly aligned and secured.
- Montaj: Lamp holder is designed for installation on a Ø10 male connector. Secure the lamp holder to the fixture using the appropriate mounting method.
- Attach Shade Ring (Optional): Eğer al kullanıyorsanızampshade, slide the shade ring over the threaded part of the lamp holder and tighten it to secure the lampgölge.
5. Operasyon
Once installed, operating the lamp holder is straightforward:
- Ampul Ekle: Gently screw an E14 screw-base bulb into the lamp Tutucuyu sıkıca oturana kadar sıkın. Aşırı sıkmayın.
- Gücü Geri Yükle: Turn on the power supply at the main circuit breaker.
- Test: Activate the light switch to confirm proper operation.
6. Bakım
The Legrand E14 Lamp Holder requires minimal maintenance.
- Temizlik: Disconnect power before cleaning. Wipe the exterior with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- Denetleme: L'yi periyodik olarak inceleyinamp holder for any signs of damage, wear, or loose connections. If any issues are found, disconnect power and address them immediately.
- Ampul Değişimi: Always disconnect power before replacing a bulb. Allow the old bulb to cool completely before removal.
7. Sorun Giderme
Eğer l ile ilgili sorunlarla karşılaşırsanızamp holder, refer to the following common problems and solutions:
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Işık yanmıyor | Güç kaynağı yok | Sigortayı ve duvar anahtarını kontrol edin. |
| Işık yanmıyor | Arızalı ampul | Replace the bulb with a new, working E14 bulb (max 60W). |
| Işık yanmıyor | Gevşek kablo bağlantısı | Disconnect power and check all wire connections within the lamp holder. Tighten if necessary. |
| Titreyen ışık | Gevşek ampul veya bağlantı | Ensure the bulb is screwed in tightly. Disconnect power and check wiring connections. |
8. Teknik Özellikler
- Marka: Legrand
- Model Numarası: Bacak91123
- Ampul Tipi: E14 Screw-base
- Malzeme: Polyamide-Imide
- Renk: Beyaz
- Cilttage: 230 Volt
- Maksimum Güç: 60 Watt
- Ürün Ölçüleri (U x G x Y): 3x3x6 cm
- Ağırlık: 50 gram
- Montaj Tipi: For Ø10 male connector
- Compliant Specifications: NF
- Menşei ülke: Çin
9. Garanti ve Destek
For warranty information or technical support, please refer to the documentation provided with your purchase or contact Legrand customer service directly. Keep your proof of purchase for warranty claims.
