Amprobe AM-570 Endüstriyel Dijital Multimetre Kullanım Kılavuzu

1. Giriş

This manual provides essential instructions for the safe and effective operation of the Amprobe AM-570 Industrial Digital Multimeter. The AM-570 is designed for professionals requiring accurate and reliable measurements in various electrical, HVAC/R, and industrial maintenance applications. Please read this manual thoroughly before using the device to ensure proper function and safety.

2. Güvenlik Bilgileri

To prevent electric shock or personal injury, and to avoid damage to the meter or the equipment under test, observe the following safety guidelines:

• Daima yerel ve ulusal güvenlik kurallarına uyun.
• The Amprobe AM-570 is rated for CAT IV 600 V and CAT III 1000 V. Do not exceed these ratings.
• Inspect test leads for damaged insulation or exposed metal before use. Replace damaged leads immediately.
• Ölçüm sırasında fonksiyon anahtarının doğru konumda olduğundan emin olun.
• Nominal hacimden fazlasını uygulamayıntage between terminals or between any terminal and ground.
• Vol ile çalışırken dikkatli oluntag30 V AC RMS, 42 V tepe veya 60 V DC'nin üzerinde voltaj değerlerine sahiptirler. Bu voltaj değerleritagşok tehlikesi yaratabilir.
• Devreye giden gücü kesin ve tüm yüksek voltajlı kabloları boşaltın.tagDirenç, süreklilik, diyot veya kapasitans testlerini yapmadan önce kapasitörleri kontrol edin.
• Do not operate the meter if it appears damaged or if it is not operating properly.
• Doğru ölçümler elde etmek için düşük pil göstergesi göründüğü anda pili değiştirin.
• Sayacın servisini yaparken yalnızca belirtilen yedek parçaları kullanın.

3. Paket İçeriği

Verify that all items listed below are present and undamaged:

• Amprobe AM-570 Industrial Digital Multimeter
• Test Leads (one pair, red and black)
• K-Type Thermocouple Probes (two)
• Taşıma Çantası
• 9V Pil (önceden takılı veya ayrı olarak dahil)
• Kullanım Kılavuzu (bu belge)

Resim 3.1: Amprobe AM-570 Digital Multimeter shown with its standard accessories, including test leads, two K-type thermocouple probes, and a soft carrying case.

4. Ürün Özellikleri

The Amprobe AM-570 offers a comprehensive set of features for diverse electrical measurements:

• AC/DC Hacmini ölçertage kadar 1000 V
• Measures AC/DC Current
• Measures Resistance, Frequency, Capacitance, and Temperature
• Measures Duty Cycle
• True-RMS technology for accurate readings in non-linear loads
• Low Z mode to detect stray voltages and eliminate ghost readings
• Low Pass Filter for accurate voltage measurements on variable frequency drives (VFDs)
• Temassız Hacimtage (NCV) detection for quick voltage presence checks
• Built-in flashlight for illumination in dimly lit areas
• Data Hold, MAX/MIN, and Peak Hold functions
• CAT IV 600 V / CAT III 1000 V safety rating

Resim 4.1: Amprobe AM-570 Digital Multimeter, showing its display, rotary dial, and function buttons. The display indicates a DC voltage reading of 119.4 V.

Resim 4.2: Açılı view of'un Amprobe AM-570 Digital Multimeter, highlighting the clear digital display, which currently shows a frequency reading of 0.000 kHz.

5. Kurulum

5.1 Pil Kurulumu

1. Sayacın KAPALI olduğundan emin olun.
2. Ölçüm cihazının arkasındaki pil bölmesini bulun.
3. Pil kapağını sabitleyen vidayı gevşetmek için bir tornavida kullanın.
4. Pil kapağını çıkarın.
5. Doğru kutuplara dikkat ederek yeni bir 9V pil takın.
6. Pil kapağını yerine takın ve vidayla sabitleyin.

5.2 Test Uçlarının Bağlanması

Always connect the black test lead to the COM (common) terminal. Connect the red test lead to the appropriate input terminal based on the measurement function:

• VΩHz: Cilt içintage, direnç, frekans, kapasitans ve diyot/süreklilik ölçümleri.
• mAμA: Milyonlarca kişi içinampve mikroampMevcut ölçümler.
• 10A: For high current (up to 10A) measurements.

Resim 5.1: Amprobe AM-570 Digital Multimeter shown with its integrated kickstand extended, allowing for hands-free viewÇalışma sırasında.

6. Kullanım Talimatları

The AM-570 features a rotary dial for selecting primary measurement functions and push buttons for secondary functions and settings.

6.1 Fonksiyon Seçimi

Turn the rotary dial to the desired measurement function. Use the SEÇME button to toggle between primary and secondary functions within a single dial position (e.g., AC/DC voltage, direnç/süreklilik/diyot).

6.2 Ölçüm Fonksiyonları

• Cilttage (V~ / V--): Select the V~ (AC) or V-- (DC) position. Connect test leads in parallel with the circuit.
• Current (10A / mAµA): Select the 10A or mAµA position. Connect the meter in series with the circuit. Ensure correct terminal connection.
• Direnç (Ω): Select the Ω position. Ensure power is off and capacitors are discharged. Connect test leads across the component.
• Continuity ())): Select the Ω position and press SEÇME until the continuity symbol appears. A continuous beep indicates continuity.
• Diode Test (→|): Select the Ω position and press SEÇME until the diode symbol appears. Connect leads across the diode.
• Kapasitans (F): Select the F position. Ensure power is off and capacitors are discharged. Connect leads across the capacitor.
• Frekans (Hz) / Görev Döngüsü (%): Select the Hz% position. Connect leads to the signal source. Press SEÇME Frekans ve görev döngüsü arasında geçiş yapmak için.
• Sıcaklık (° C / ° F): Select the TEMP °C/°F position. Insert K-type thermocouple probes into the T1 and T2 inputs. Press SEÇME to toggle between Celsius and Fahrenheit.
• Temassız Hacimtage (NCV): Select the NCV position. Hold the top of the meter near a live conductor. The NCV indicator and audible alarm will activate if voltage tespit edildi.
• Low Z Mode: Select the LoZ V~ position for AC voltage measurements with low impedance. This helps to eliminate ghost voltagee.
• Alçak Geçirgen Filtre: Activated automatically in certain AC voltage modes, this filter allows for accurate measurements on variable frequency drives.

6.3 Özel Fonksiyonlar

• RANGE: Manually select the measurement range instead of auto-ranging.
• REL (Göreli Mod): Measures the difference between a stored reference value and the current reading.
• MAKSİMUM/MİNİMUM: Records the maximum and minimum values over a measurement period.
• TUTMAKEkrandaki mevcut değeri dondurur.
• PEAK (1ms): Captures fast transient peaks (positive and negative) with a 1ms response time.

Image 6.1: An electrician utilizing the Amprobe AM-570 Digital Multimeter to perform voltage measurements within an industrial electrical panel, demonstrating practical application.

7. Bakım

7.1 Temizlik

Sayaçları reklamla silinamp Bez ve yumuşak deterjan kullanın. Aşındırıcı veya çözücü maddeler kullanmayın. Kullanmadan önce ölçüm cihazının kuru olduğundan emin olun.

7.2 Pil Değişimi

Refer to Section 5.1 for detailed instructions on replacing the 9V battery. Replace the battery promptly when the low battery indicator appears on the display.

7.3 Sigorta Değişimi

If the current measurement functions cease to operate, the internal fuses may need replacement. Fuse replacement should only be performed by qualified personnel. Refer to the full service manual for fuse specifications and replacement procedures. Always use fuses with the specified voltage ve mevcut derecelendirmeler.

7.4 Depolama

When not in use for extended periods, remove the battery to prevent leakage. Store the meter in a cool, dry environment, preferably in its carrying case.

8. Sorun Giderme

9. Özellikler

10. Garanti ve Destek

Amprobe products are designed for reliability and performance. This product is covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Ampelbise webalan.

For technical support, service, or replacement parts, please contact Amprobe customer service. Contact information can typically be found on the Ampelbise webSitede veya ürün ambalajında.