Nissan 41060-AX085 Disk Fren Balata Seti Kullanım Kılavuzu

1. Giriş

This manual provides essential information for the proper handling, installation, and maintenance of the Nissan 41060-AX085 Disc Brake Pad Kit. This product is a genuine Original Equipment Manufacturer (OEM) part, designed to meet Nissan's stringent quality and performance standards. Adherence to these instructions is crucial for ensuring optimal braking performance and vehicle safety.

2. Güvenlik Bilgileri

WARNING: Improper installation or maintenance of brake components can lead to serious injury or death. Brake system work should only be performed by qualified personnel or a certified mechanic.

• Always wear appropriate personal protective equipment, including safety glasses and gloves, when working on vehicle brake systems.
• Herhangi bir işe başlamadan önce aracın düz bir zeminde kriko ayakları üzerinde güvenli bir şekilde desteklendiğinden emin olun. Asla sadece krikoya güvenmeyin.
• Ayrıntılı talimatlar ve tork özellikleri için aracınızın özel servis kılavuzuna bakın.
• Fren hidroliğini boyalı yüzeylerden uzak tutun, çünkü boyaya zarar verebilir.
• Do not reuse old brake hardware unless explicitly stated in the vehicle service manual.

3. Paket İçeriği

The Nissan 41060-AX085 Disc Brake Pad Kit typically includes the following components:

• Genuine Nissan 41060-AX085 Disc Brake Pads (set for one axle)

Figure 1: Genuine Nissan 41060-AX085 Disc Brake Pads. This image displays two pairs of disc brake pads, each consisting of a backing plate with friction material. These are the primary components included in the kit for one axle of a vehicle.

4. Kurulum ve Kurulum

Bu bölüm genel birview of disc brake pad replacement. Always consult your vehicle's specific service manual for detailed, model-specific instructions.

Gerekli Araçlar (Tipik):

• Jack ve Jack Standları
• Lug Anahtarı
• Lokma Anahtar Takımı ve Cırcır
• C-clamp veya Fren Kaliperi Piston Kompresörü
• Tel fırça
• Fren temizleyici
• Tork Anahtarı
• New Brake Hardware (if not included and recommended)

Kurulum Adımları (Genel):

1. Aracı Hazırlayın: Park the vehicle on a level surface, engage the parking brake, and block the wheels. Loosen the lug nuts on the wheel(s) to be serviced.
2. Kaldır ve Sabitle: Jack up the vehicle and support it securely with jack stands. Remove the lug nuts and the wheel.
3. Kaliperi Çıkarın: Locate the brake caliper. Remove the caliper guide pin bolts (usually two). Carefully slide the caliper off the rotor and support it without letting it hang by the brake hose.
4. Eski Pedleri Çıkarın: Eski fren balatalarını kaliper braketinden çıkarın. Yönlerine dikkat edin.
5. Temizleyin ve inceleyin: Clean the caliper bracket and caliper with a wire brush and brake cleaner. Inspect the brake rotor for wear, scoring, or damage. Replace if necessary.
6. Pistonu Sıkıştırma: C-cl kullanınamp or brake caliper piston compressor to slowly push the caliper piston(s) back into the caliper bore. This creates space for the new, thicker pads.
7. Yeni Balataları Takın: Install the new Nissan 41060-AX085 brake pads into the caliper bracket, ensuring they are correctly seated and oriented. Apply a thin layer of brake lubricant to the caliper guide pins and any metal-to-metal contact points on the pads (excluding the friction material).
8. Caliper'ı yeniden takın: Carefully slide the caliper back over the new pads and rotor. Reinstall the caliper guide pin bolts and tighten them to the manufacturer's specified torque.
9. Tekerleği yeniden takın: Tekerleği tekrar takın ve bijon somunlarını elle sıkın.
10. Aracı İndir: Lower the vehicle to the ground and tighten the lug nuts to the manufacturer's specified torque in a star pattern.
11. Pompa Frenleri: Before driving, slowly pump the brake pedal several times until a firm pedal feel is achieved. This seats the pads against the rotor and restores proper pedal travel. Check the brake fluid reservoir level and top off if necessary.

5. Çalıştırma ve İlk Çalıştırma Prosedürü

After installing new brake pads, a proper break-in (bedding-in) procedure is essential for optimal performance and longevity. This process transfers a thin, even layer of friction material from the pads to the rotors.

Brake Pad Break-in Steps:

1. Kesintisiz olarak birkaç duraklama yapabileceğiniz güvenli ve açık bir alan bulun.
2. Accelerate to approximately 30-35 mph (50-55 km/h) and apply moderate braking pressure to slow down to about 5-10 mph (8-16 km/h). Do not come to a complete stop.
3. Repeat this process 5-6 times, allowing a short cool-down period between each stop. Avoid heavy braking during this phase.
4. After the initial series of stops, drive for several minutes without using the brakes to allow them to cool completely.
5. Perform another 2-3 stops from a slightly higher speed (e.g., 40-45 mph or 65-70 km/h) with slightly firmer pressure, again slowing to 5-10 mph without stopping completely.
6. Allow the brakes to cool completely before resuming normal driving.

During the break-in period, avoid sudden, hard stops and prolonged braking (e.g., riding the brakes down a long hill).

6. Bakım

Fren sisteminizin düzenli olarak kontrol edilmesi ve bakımı, güvenlik ve performans açısından hayati önem taşır.

• Periyodik muayene: Inspect brake pads, rotors, calipers, and brake lines at least once a year or every 12,000 miles (20,000 km), or as recommended by your vehicle manufacturer.
• Ped Kullanımı: Check the thickness of the friction material. Replace pads when they reach their minimum wear limit, typically indicated by a wear indicator or when the friction material is approximately 2-3mm thick.
• Fren Sıvısı: Check brake fluid level regularly. A low level can indicate worn pads or a leak. Consult your vehicle manual for recommended brake fluid type and replacement intervals.
• Gürültü: Pay attention to any unusual noises (squealing, grinding) from the brakes, which may indicate wear or a problem.

7. Sorun Giderme

This section addresses common issues that may arise with brake pads.

Yaygın Sorunlar:

• Fren Cıyaklaması/Gürültüsü:
  • Neden: Improper installation, lack of anti-squeal shims/lubricant, worn pads, or glazed rotors.
  • Çözüm: Re-check installation, ensure shims are present and properly lubricated, inspect pads for wear, and rotors for glazing.
• Poor Braking Performance:
  • Neden: Improper break-in, air in the brake lines, contaminated pads, or worn components.
  • Çözüm: Perform break-in procedure, bleed brake lines, inspect pads for contamination (oil/grease), and check other brake components.
• Titreşim/Nabız:
  • Neden: Warped rotors, uneven pad wear, or loose wheel bearings.
  • Çözüm: Inspect rotors for runout and replace if warped. Check for even pad wear and inspect wheel bearings.
• Dengesiz Balata Aşınması:
  • Neden: Sticking caliper piston, seized caliper guide pins, or improper installation.
  • Çözüm: Inspect and service calipers, lubricate guide pins, and ensure proper pad installation.

If you experience persistent brake issues, consult a qualified mechanic immediately.

8. Özellikler

9. Garanti ve Destek

As a Genuine Nissan Part, this product is covered by Nissan's standard warranty for OEM replacement parts. Warranty terms and conditions may vary by region and purchase location. Please retain your proof of purchase.

For specific warranty details or technical support, please contact your authorized Nissan dealer or visit the official Nissan automotive parts website. When contacting support, please have your vehicle's VIN (Vehicle Identification Number) and the part number (41060-AX085) available.