Intermatic ET1105C 24-Hour Electronic Time Switch Instruction Manual

giriiş

This manual provides instructions for the installation, operation, and maintenance of the Intermatic ET1105C 24-Hour Electronic Time Switch. This device is designed to control electrical loads with precise, programmable timing, offering an upgrade from mechanical time switches with features like up-to-the-minute programming, battery backup, and automatic daylight saving time corrections.

Önemli Güvenlik Bilgileri

UYARI: Yangın veya Elektrik Çarpması Riski

• Plastik muhafazalar için, boru bağlantıları arasındaki bağlantı otomatik değildir ve kurulumun bir parçası olarak sağlanmalıdır.
• Güç kesme noktası görüş alanı dışındaysa, KAPALI konuma kilitleyin ve tag Beklenmedik güç kullanımını önlemek için.
• Ensure there is no wire insulation under the terminal plate on the time switch connector. Firmly tighten terminal screws.
• Gücü AÇIK duruma getirmeden önce plastik yalıtkan kaplama terminallerini değiştirin.
• Servis yapmadığınız zamanlarda KAPIYI HER ZAMAN KAPALI TUTUN.

AVERTISSEMENT: Risque d'incendie ou de choc électrique

Pour les boîtiers en plastique, la liaison entre les raccordements de conduits n'est pas automatique et doit être prévue dans le cadre de l'installation.

Ürün Bittiview

Image: Intermatic ET1105C Electronic Time Switch with its protective cover open, revealing the digital display, control buttons (MODE, RESET, ENTER/NEXT, ON/OFF, +, -), and the wiring terminal block at the bottom. The internal wiring diagram and specifications are visible on the left panel.

The Intermatic ET1105C is an electronic 24-hour time switch designed for direct control of loads up to 30 amps resistive or inductive, and tungsten loads. It features battery-powered carryover for program retention during power outagee.

Kontrol Paneli

• MOD Düğmesi: Cycles through programming menus.
• Yeniden başlatma tuşu: Clears memory.
• ENTER/NEXT Button: Confirms selections and advances to the next step.
• AÇIK/KAPALI Düğmesi: Manually turns the load ON or OFF, or toggles events.
• + / - Düğmeleri: Adjusts values (date, time, event settings).
• LCD Ekran: Shows current time, date, program status, and load status.

Kurulum

Cilttage Seçim

The ET1105C supports multi-volt operation from 120 to 277 VAC, 50/60 Hz. Refer to the internal instruction manual or wiring diagram for specific voltage selection procedures.

Kablolama

Wiring should be performed by a qualified electrician in accordance with all local and national electrical codes.

1. Kurulum işlemine başlamadan önce devrenin ana şalterinden tüm elektriğin kesildiğinden emin olun.
2. Mount the time switch securely in the desired location.
3. Güç kaynağı kablolarını belirtilen terminallere bağlayın.
4. Connect the load wires to the appropriate output terminals.
5. Ensure all terminal screws are firmly tightened and no wire insulation is caught under the terminal plate.
6. Replace the plastic insulator covering the terminals before restoring power.

Refer to the wiring diagram printed on the inside of the enclosure for detailed connection instructions.

Kullanım Talimatları

Manuel AÇMA/KAPAMA Çalışması

In either AUTO or MANUAL mode, press the AÇIK/KAPALI button to manually toggle the load. The display will indicate if the load is currently ON or OFF.

Programlama Adımları

The time switch allows for up to 28 events (14 ON / 14 OFF).

1. Menülere Erişim: Basın MOD button repeatedly to cycle through the programming menus (DATE, TIME, ON/OFF EVENTS).
2. Ayar Tarihi: When "SET DATE" appears, use the + or - keys to enter the current date. Press GİRMEK onaylamak için.
3. Ayarlanma Süresi: When "SET CLOCK" appears, use the + or - keys to enter the current time. Press GİRMEK onaylamak için.
4. Setting ON/OFF Events: When "ON/OFF EVENTS" appears, press the + or - button. The display will show "12:00 AM" with the load status (ON/@) and event number. Use the + or - keys to set the desired ON or OFF time and day(s) for the event. Press the AÇIK/KAPALI load button to toggle the load status (ON or OFF). To clear an event, select "(nil)". Press GİRMEK to save the event and move to the next event, or press MOD to advance to AUTO run mode.

Otomatik Mod (OTOMATİK)

Basın MOD button repeatedly until "AUTO" appears on the display. In AUTO mode, the time switch will execute the programmed ON/OFF events. Manual overrides using the AÇIK/KAPALI load button are temporary and will revert to the programmed schedule at the next event.

Düzenleme ve YenidenviewEtkinlikler

Events can be edited or reviewed by returning to the appropriate menu using the MOD düğme.

Bakım

Pil Değişimi

The time switch uses two industrial-grade AAA standard non-rechargeable 1.5-volt alkaline batteries for program retention.

1. To replace the battery, locate the battery tray.
2. Pull the battery tray out and downward to remove the battery holder.
3. Doğru kutuplara dikkat ederek pilleri değiştirin.
4. The batteries should be replaced approximately every 3 years after installation.

Özellikler

Garanti

This product comes with a 1-year limited warranty. For detailed warranty information and claims, please contact Intermatic customer support.

Destek

For technical assistance, troubleshooting, or further information, please visit the official Intermatic websitesine bakın veya müşteri hizmetleri departmanıyla iletişime geçin.

Intermatic Incorporated, Spring Grove, Illinois 60081-9698