1. Giriş
The Amprobe LAN-1 LAN Cable Tester is a diagnostic tool designed to identify and trace data cables and connectors. It helps detect common wiring issues such as shorts, miswirings, and open circuits in various cable types. This manual provides detailed instructions for the proper use, setup, and maintenance of your LAN-1 tester.
The LAN-1 evaluates most common cable types, including 10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, and Token Ring cables, as well as RJ45 and BNC connectors. It can test cables up to 300 meters long and uses LED indicators and an audible buzzer to signal cable status and errors.
2. Güvenlik Bilgileri
Lütfen çalıştırmadan önce tüm güvenlik talimatlarını okuyun ve anlayın. Amprobe LAN-1 LAN Cable Tester. Failure to follow these instructions may result in injury or damage to the device.
- Cihazın hasarlı olduğu veya düzgün çalışmadığı görülüyorsa cihazı kullanmayın.
- Ensure the correct battery type and polarity are used during installation.
- Cihazı aşırı sıcaklıklara, neme veya doğrudan güneş ışığına maruz bırakmaktan kaçının.
- Cihazı kendiniz tamir etmeye veya değiştirmeye çalışmayın. Tüm servis işlemlerini yetkili personele yaptırın.
- Always disconnect the cable tester from any active network or power source before performing maintenance or battery replacement.
3. Paket İçeriği
Aşağıda listelenen tüm öğelerin paketinizde mevcut olduğundan emin olun:
- LAN-1 LAN Cable Tester
- (1) Remote terminator
- (1) RJ45 to female BNC cable
- (1) RJ45 to male BNC cable
- (1) RJ45 to RJ45 cable
- (1) Female BNC to female BNC cable
- (1) 9V battery (installed)
- Talimatlar (bu kılavuz)
4. Ürün Bittiview
The Amprobe LAN-1 features a compact design with intuitive controls and clear LED indicators for efficient cable testing.
4.1 Temel Özellikler
- Cable Testing: Locates and traces data cables and connectors to identify shorts, miswiring, and opens.
- Çok Yönlü Uyumluluk: Evaluates 10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, and Token Ring cables, along with RJ45 and BNC connectors.
- Hata Göstergesi: An audible buzzer indicates an error condition in the cable.
- Genişletilmiş Menzil: Tests cables up to 300 meters long.
- Ekranı Temizle: Eighteen red and green LEDs indicate the source or test results.
- Test Modları: Supports Loopback Test and Remote Test functions.
- Güvenlik Uyumluluğu: CE - EMC certified.
4.2 Bileşen Tanımlama
Şekil 1: Ön view of'un Amprobe LAN-1 LAN Cable Tester. This image displays the main unit with its LED pin-out indicator, battery status light, and control buttons including AUTO, MAN, HOLD, TEST, BATT, and the power button.
Şekil 2: Amprobe LAN-1 LAN Cable Tester showing the main unit and the remote terminator module. This view highlights how the remote unit connects to the main tester for comprehensive cable testing.
- PIN-OUT INDICATOR LEDs: Displays the wiring status for each pin (1-8) and ground (G).
- BATT LED: Pil durumunu gösterir.
- OTOMATİK Düğme: Initiates automatic scanning of cable pins.
- MAN Button: Allows manual step-through of cable pins.
- TUTMA Düğmesi: Pauses the current test result display.
- TEST Düğmesi: Starts a test cycle.
- POWER Button (Yellow): Cihazı açıp kapatır.
- RJ45 Bağlantı Noktası: For connecting RJ45 cables.
- BNC Port: For connecting BNC cables.
- Remote Terminator: A separate module used for testing installed cables or long runs.
5. Kurulum
5.1 Pil Kurulumu
The LAN-1 tester is powered by one 9V battery, which is typically pre-installed. If replacement is needed:
- Cihazın kapalı olduğundan emin olun.
- Ana ünitenin arka tarafında bulunan pil bölmesi kapağını bulun.
- Remove the screw(s) securing the cover and carefully open it.
- Remove the old 9V battery and disconnect it from the terminals.
- Connect a new 9V battery, ensuring correct polarity (+ to + and - to -).
- Pili bölmeye yerleştirin ve kapağı vida(lar)la sabitleyerek yerine takın.
The battery provides power for up to 20 hours of testing.
5.2 Test için Bağlantı Kabloları
Before testing, ensure the cable is disconnected from any active network equipment.
- For patch cables (short cables not installed in walls): Connect one end of the cable to the RJ45 or BNC port on the main unit and the other end to the corresponding port on the remote terminator.
- For installed cables (e.g., wall plates, patch panels): Connect one end of the cable to the RJ45 or BNC port on the main unit. Connect the remote terminator to the other end of the installed cable (e.g., at the wall plate in another room).
6. Kullanım Talimatları
6.1 Açma/Kapatma
Sarıya basın GÜÇ Cihazı açmak için düğmeye basın. Cihazı kapatmak için tekrar basın.
6.2 Bir Testin Gerçekleştirilmesi
Once the cable is connected, you can perform a test:
- Basın TEST button to initiate a cable test.
- Automatic Scan (AUTO mode): Basın OTOMATİK button. The tester will automatically scan through each pin (1-8 and G) and display the results sequentially. This is suitable for quick checks.
- Manual Scan (MAN mode): Basın ADAM button. Each press of the ADAM button will advance the test to the next pin, allowing for a detailed examination of each connection.
- Tutma İşlevi: Basın TUTMAK button to pause the current display of the pin-out indicator. Press it again to resume scanning.
6.3 LED Göstergelerinin Yorumlanması
The 18 red and green LEDs on the PIN-OUT INDICATOR provide visual feedback on the cable's status:
- Yeşil LED: Indicates a correct connection for the corresponding pin.
- Kırmızı LED: Indicates an error for the corresponding pin (e.g., open circuit, short circuit, miswiring).
- LED yok: May indicate an open circuit or a broken wire for that pin.
- Zil: An audible buzzer will sound when an error condition is detected, providing an additional alert.
The LEDs on the remote module will mirror the main unit's display for the corresponding pins, allowing for verification of end-to-end continuity.
6.4 Pil Durum Kontrolü
Basın SİLAH button to check the battery level. The BATT LED will illuminate if the battery has sufficient power. If the BATT LED does not light up or is dim, replace the 9V battery.
7. Bakım
7.1 Temizlik
To ensure the longevity and proper functioning of your LAN-1 tester, keep it clean and free from dust and debris.
- Cihazın dış yüzeyini yumuşak bir bezle silin.amp bezle silin. Aşındırıcı temizleyiciler veya çözücüler kullanmayın.
- Ensure no moisture enters the ports or battery compartment.
7.2 Pil Değişimi
Replace the 9V battery when the BATT LED indicates low power or if the device fails to power on. Refer to Section 5.1 for detailed battery installation instructions.
Kullanılmış pilleri daima yerel düzenlemelere uygun şekilde atın.
8. Sorun Giderme
Eğer sorunlarla karşılaşırsanız Amprobe LAN-1 LAN Cable Tester, refer to the following common problems and solutions:
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Cihaz açılmıyor. | Akü zayıf veya bitmiş; akü yanlış takılmış. | 9V pili, doğru kutuplara dikkat ederek değiştirin. |
| No LED activity during test. | Cable not properly connected; faulty cable; remote terminator not connected. | Ensure cables are securely connected to both the main unit and remote terminator. Test with a known good cable. |
| Buzzer sounds continuously or unexpectedly. | Short circuit or severe miswiring detected. | Examine the cable for physical damage or incorrect wiring. Check connectors for bent pins. |
| Inconsistent test results. | Loose connections; intermittent cable fault; low battery. | Ensure all connections are tight. Replace battery. Try wiggling the cable during test to identify intermittent faults. |
9. Özellikler
| Örnek | LAN-1 |
| Güç Kaynağı | (1) 9V battery |
| Pil Ömrü | Up to 20 hours of tests |
| Test Edilen Kablo Türleri | 10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, Token Ring cables |
| Cable Connector Types | RJ45 and BNC |
| Maksimum Satır Uzunluğu | 300m |
| Ağırlık | 0.6 lb. / 0.27 kg (approx. 9.5 ounces) |
| Boyutlar (Y x G x D) | 5.1 x 2.2 x 1.5 in. / 130 x 56 x 38mm |
| Görüntülemek | 18 LEDs (9 Red and 9 Green), 9 LEDs on Remote module |
| Güvenlik Uyumluluğu | CE - EMC |
10. Garanti Bilgileri
The Amprobe LAN-1 LAN Cable Tester comes with a Bir Yıllık Sınırlı Garanti. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accident, modification, neglect, or unauthorized repair.
For specific warranty terms and conditions, please refer to the warranty card included with your product or contact Amprobe customer support.
11. Müşteri Desteği
If you have any questions, require technical assistance, or need to report a problem with your Amprobe LAN-1 LAN Cable Tester, please contact Amprobe customer support.
Lütfen yetkiliyi ziyaret edin Ampelbise webEn güncel iletişim bilgileri ve destek kaynakları için siteyi ziyaret edin.
Çevrimiçi Kaynaklar: www.ampbornoz.com
