giriiş
The Zircon StudSensor Pro LCD is an electronic stud finder designed to quickly and easily locate the edges of wood and metal studs and joists behind walls, floors, and ceilings. It features an easy-to-read display, the patented SpotLite Pointing System, and Wire Warning detection for live AC-Voltage.
Güvenlik Bilgileri
- Always exercise caution when scanning walls, ceilings, and floors that may contain electrical wiring or plumbing.
- The Wire Warning detection indicates the presence of live, unshielded electrical wiring. Shielded wires may not be detected.
- Do not rely solely on the stud finder to avoid hazards. Always turn off power to circuits before cutting or drilling into walls.
- Bu alet yalnızca iç mekanda kullanım için tasarlanmıştır.
Paket İçeriği
- Zircon StudSensor Pro LCD Tool
- Kullanım Kılavuzu (bu belge)
- How-to Z-Card
Ürün Özellikleri
- Stud Scan Mode: Locates edges of wood or metal studs up to 3/4 inch (19 mm) deep.
- DeepScan Mode: Doubles scanning depth to 1-1/2 inches (38 mm) for thicker walls.
- Okunması Kolay LCD Ekran: Clearly indicates stud edges and other information.
- Patented SpotLite Pointing System: Shines a beam of light on the wall to identify the target.
- Audio Tone: Provides audible alerts when a stud edge is reached.
- Kablo Uyarı Algılama: Indicates the presence of live, unshielded electrical wiring up to 2 inches (51 mm) deep.
- "Over-the-Stud" Indicator: Alerts the user if scanning begins over a stud, prompting a new starting location.
- TruCal Technology: Calibrates to any wall's density, with an icon indicating readiness.
Şekil 1: Ön view of the Zircon StudSensor Pro LCD, showing the display, mode switch, and the SpotLite beam.
Kurmak
1. Pil Kurulumu
- Ünitenin arkasında bulunan pil bölmesi kapağını açın.
- Yeni bir 9V alkalin pili, doğru kutuplara (+/-) dikkat ederek takın.
- Pil bölmesi kapağını sıkıca kapatın.
2. Power On and Calibration
- Place the tool flat against the wall where you intend to scan. Ensure it is not over a stud or dense material.
- Press and hold the Power Button. The unit will emit a short beep, and the TruCal icon will appear on the LCD, indicating calibration.
- Keep the tool flat against the wall and still until the TruCal icon disappears and the unit beeps again, signaling successful calibration.
- If the "over-the-stud" indicator appears, release the Power Button, move the tool to a different location, and recalibrate.
Kullanım Talimatları
1. Selecting a Scan Mode
Use the slide switch on the front of the tool to select either Stud Taraması or Derin tarama mod.
Şekil 2: Taraf view of the Zircon StudSensor Pro LCD, highlighting the mode selection switch.
2. Scanning for Studs
- After calibration, keep the Power Button pressed and slowly slide the tool horizontally across the wall surface.
- As the tool approaches a stud, the LCD display will show increasing bars, indicating proximity.
- When the tool detects the edge of a stud, the SpotLite Pointing System will illuminate, an audio tone will sound, and the "EDGE" indicator will appear on the LCD. Mark this spot.
- Continue sliding past the stud until the indicators turn off. Then, slide back from the opposite direction to locate the other edge of the stud. Mark this second spot.
- The center of the stud is typically between these two marked edges.
Şekil 3: A user operating the Zircon StudSensor Pro LCD on a wall to locate studs.
3. Wire Warning Detection
The Wire Warning detection icon will appear on the LCD and an audible alert will sound if live, unshielded AC electrical wiring is detected within approximately 2 inches (51 mm) of the wall surface. This feature is active in both Stud Scan and DeepScan modes.
Uyarı: Always turn off power to circuits before drilling or cutting into walls.
Bakım
- Keep the tool clean and dry. Wipe with a soft, damp Gerekirse bezle silin. Aşındırıcı temizleyiciler veya çözücüler kullanmayın.
- Remove the battery if the tool will not be used for an extended period to prevent leakage.
- Store the tool in a cool, dry place, away from direct sunlight and extreme temperatures.
Sorun giderme
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Ünite açılmıyor. | Pil bitmiş veya yanlış takılmış. | Replace with a fresh 9V alkaline battery, ensuring correct polarity. |
| Inaccurate readings or "over-the-stud" indicator appears frequently. | Improper calibration; scanning over dense material or a stud. | Release the Power Button, move the tool to a different, clear spot on the wall, and recalibrate. Ensure the tool is flat against the wall during calibration. |
| Wire Warning detection is always on or erratic. | Presence of live wiring, or interference from other electronic devices. | Confirm if live wiring is present. Move away from other electronics. Recalibrate in a different area. |
| Cannot find studs. | Wall material too thick; studs are deeper than scan depth; unusual wall construction. | Switch to DeepScan mode. Try scanning from multiple directions. Note that some materials (e.g., lath and plaster, metallic wallpaper) can interfere with detection. |
Özellikler
- Modeli: SS Pro LCD
- Stud Scan Depth: 3/4 inçe (19 mm) kadar
- DeepScan Depth: Up to 1-1/2 inches (38 mm)
- style="color:#333333;">Wire Warning Detection Depth: Up to 2 inches (51 mm) for live, unshielded AC wires
- Güç Kaynağı: 9V alkaline battery (not included)
- Çalışma Sıcaklığı: 20°F ila 120°F (-7°C ila 49°C)
- Depolama Sıcaklığı: -20°F ila 150°F (-29°C ila 66°C)
- Boyutlar: Yaklaşık 6 x 12 x 4 inç (15.2 x 30.5 x 10.2 cm)
- Ağırlık: Approximately 9.6 ounces (272 grams) without battery
- Malzeme: Plastik
- Renk: Sarı
Garanti ve Destek
Sınırlı Garanti
Zircon Corporation warrants this product to be free from defects in materials and workmanship for bir yıl from the date of purchase. This warranty does not cover damage due to misuse, abuse, or normal wear and tear.
Müşteri Desteği
For technical assistance or warranty claims, please visit the official Zircon websitesine bakın veya müşteri hizmetleri departmanıyla iletişime geçin.
