giriiş
This manual provides essential information for the proper installation, operation, and maintenance of your Irritrol 2713APR Electric Anti-Siphon Valve. This valve is designed for residential irrigation applications, offering reliable performance and precise flow control. Please read these instructions thoroughly before installation and use.
Güvenlik Bilgileri
- Always turn off the main water supply before installing or performing maintenance on the valve.
- Tüm elektrik bağlantılarının yetkili bir profesyonel tarafından yapıldığından ve yerel yönetmeliklere uygun olduğundan emin olun.
- Do not exceed the maximum operating pressure of 150 PSI or maximum water temperature of 110°F (43°C).
- Protect the valve from freezing temperatures.
Ürün Bittiview
The Irritrol 2713APR is a 1-inch electric anti-siphon valve featuring a stainless bonnet and flow control. It includes a built-in atmospheric vacuum breaker to prevent back-siphonage, ensuring water safety. The valve allows for both electric and manual operation.
Şekil 1: Irritrol 2713APR Electric Anti-Siphon Valve. This image shows the grey valve assembly with a black solenoid and flow control knob. The top of the valve is labeled "1" VALVE Irritrol 150 PSI MAX 110°F H₂O MAX ASSEMBLED IN MEXICO".
Kurulum ve Yükleme
- Siteyi Hazırlayın: Ensure the installation location is above the highest sprinkler head to allow the anti-siphon feature to function correctly. The valve should be easily accessible for maintenance.
- Su Kaynağını Kapatın: Locate and turn off the main water supply to the irrigation system.
- Tesisatı Bağlayın: The valve has 1-inch inlet and outlet connections. Connect the incoming water line to the inlet and the outgoing irrigation line to the outlet. Use appropriate plumbing fittings and thread sealant to ensure watertight connections. The valve is designed for a flow range of 0.25 to 30 GPM and a pressure range of 10 to 150 psi.
- Elektrik Tesisatı: Connect the valve's solenoid wires to your irrigation controller's common and zone wires. Ensure all electrical connections are secure and protected from moisture. Refer to your irrigation controller's manual for specific wiring instructions.
- Sızıntıları Kontrol Edin: Slowly turn on the main water supply and inspect all connections for leaks. Tighten any leaking connections as necessary.
- Initial Flush (Optional): The valve features internal and external bleed (flush mode) for manual operation. To flush the system, you can manually activate the valve to clear any debris before automatic operation.
Kullanım Talimatları
- Otomatik çalışma: Once installed and wired, the valve will operate automatically according to the programming of your irrigation controller.
- Manuel İşlem:
- To manually open the valve, turn the solenoid counter-clockwise approximately one-half turn.
- To manually close the valve, turn the solenoid clockwise until snug. Do not overtighten.
- Alternatively, use the external bleed screw (if present) to manually open the valve for flushing or testing.
- Akış Kontrol Ayarı: The valve is equipped with a flow control knob.
- To decrease water flow, turn the flow control knob clockwise.
- To increase water flow, turn the flow control knob counter-clockwise.
- Adjust the flow control to achieve the desired sprinkler performance for the zone.
Bakım
Regular maintenance ensures the longevity and optimal performance of your Irritrol valve.
- Kışlama: In areas subject to freezing temperatures, properly winterize your irrigation system, including the valve, to prevent damage. This typically involves draining water from the system or using an air compressor to blow out the lines.
- Enkaz Kontrolü: Periodically inspect the valve for any debris that may have entered the system and could impede proper operation. If necessary, turn off the water, disassemble the valve bonnet (by unscrewing the screws on the top), and clean any internal components.
- Solenoid Inspection: Check the solenoid for proper function. If the valve fails to open or close electrically, the solenoid may need to be replaced.
- Diyafram Muayenesi: If the valve is not operating correctly, the diaphragm inside may be worn or damaged. Turn off the water, remove the bonnet, and inspect the diaphragm for tears or blockages. Replace if necessary.
Sorun giderme
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Vana açılmıyor | No power to solenoid, clogged diaphragm, faulty solenoid, low water pressure. | Check wiring connections, clean diaphragm, test/replace solenoid, verify water pressure. |
| Valve does not close completely (leaks) | Debris in valve, worn diaphragm, overtightened flow control. | Turn off water, clean internal components, replace diaphragm, loosen flow control slightly. |
| Düşük su akışı | Partially closed flow control, clogged filter/screen, low main water pressure. | Adjust flow control, clean any internal screens, check main water supply. |
| Water continuously flows (valve stuck open) | Debris preventing diaphragm from sealing, damaged diaphragm, faulty solenoid. | Turn off water, clean valve internals, replace diaphragm, replace solenoid. |
Özellikler
- Modeli: 2713APR
- Malzeme: Stainless Steel (Bonnet)
- Giriş/Çıkış Bağlantı Boyutu: 1 inç
- Giriş Bağlantı Tipi: Flanş
- Çıkış Bağlantı Tipi: NPT
- Port Sayısı: 2
- Akış Aralığı: 0.25 - 30 GPM
- Basınç Aralığı: 10 ila 150 PSI
- Maksimum Su Sıcaklığı: 110°F (43°C)
- Ürün Ölçüleri (U x G x Y): 6 x 6.88 x 3 inç
- Ürün Ağırlığı: 1.2 pound
- Üretici: İritrol
- UPC: 090258044253
Garanti ve Destek
For specific warranty information and technical support, please refer to the official Irritrol website or contact Irritrol customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.
İletişim Bilgileri: Please visit the official Irritrol webEn güncel iletişim bilgileri ve destek kaynakları için siteyi ziyaret edin.
