Kılavuzlar+

BFT Mitto B RCB02 R1, RCB04 R2, MITTO 2, 4, MITTO2A, MITTO4A, KLEIO B RCA 02/04

BFT Mitto Series Garage Door Remote Control Instruction Manual

Models: Mitto B RCB02 R1, RCB04 R2, MITTO 2, 4, MITTO2A, MITTO4A, KLEIO B RCA 02/04

1. Giriş

This manual provides instructions for the setup, operation, and maintenance of your BFT Mitto series garage door remote control. These remotes are designed for use with compatible BFT receivers, operating on a 433.92MHz frequency with rolling code technology. Please read these instructions carefully before attempting to program or use your new remote control.

Multiple BFT remote controls, indicating available quantities of 10, 20, or 30 pieces.
Figure 1: BFT Mitto Series Remote Controls (available in various pack sizes)

2. Uyumlu Modeller

Your new remote control is compatible with the following BFT models:

  • MITTO 2 / MITTO 4
  • MITTO2M / MITTO4M
  • MITTO B RCB 02
  • MITTO B RCB 04
  • KLEIO B RCA 02
  • KLEIO B RCA 04
  • TRC1 / TRC2 / TRC4

Önemli Not: Access to your receiver/opener is required for programming. Please ensure you have physical access to the receiver before purchasing or attempting to program the remote.

A BFT remote control shown alongside several older remote models and a battery, illustrating its compatibility as a replacement.
Figure 2: BFT Remote Control and compatible older models
Image showing two remote controls labeled 'MITTO COOL C2' and 'MITTO COOL C4' with red 'X' marks, indicating they are not compatible.
Figure 3: Incompatible models (MITTO COOL C2 and C4)

3. Özellikler

  • Yedek Uzaktan Kumanda: Ideal for replacing lost or damaged original BFT remote controls.
  • Kolay Eşleştirme: Designed for straightforward programming with your existing BFT receiver.
  • Rolling Code Technology: Provides enhanced security for your garage door or gate.
  • Uzun mesafe: Operates effectively within a range of 30m-50m in open areas.
  • Önceden Takılmış Pil: Comes with a battery included for immediate use after programming.
A hand holding the BFT remote control, with thought bubbles showing a gate, a barrier, and another gate, illustrating its use for various access systems.
Figure 4: Remote control application examples

4. Özellikler

ÖzellikDetay
MarkaBFT
Type of ProgrammingAlıcı ile programlama
Sıklık433.92MHz
Kodlama YöntemiYuvarlanan Kod
Düğmeler2 veya 4
Menzil30m-50m (open area)
PilDahil
SertifikasyonCE
KökeniÇin anakarası
Back of the BFT remote control, showing '12V === Type B RCB' and CE marking.
Figure 5: Back of the remote control with specifications
A BFT remote control with '433.92MHZ' text, next to an image of a car in a garage, highlighting the operating frequency and application.
Figure 6: Remote control frequency and typical use

5. Kurulum ve Programlama

To program your new BFT remote control, you will need to access the receiver unit of your garage door opener or gate system. The programming process involves interacting with buttons on the receiver board.

Programlama Adımları:

  1. Alıcıyı bulun: Open the motor housing of your garage door or gate system to access the receiver board. Refer to Figure 7 for a typical receiver layout.
  2. Programlama Modunu Başlat: Press either the SW1 or SW2 button on the receiver board until the LED light on the receiver starts to flash.
  3. Pair Remote Buttons (First Line): Simultaneously press buttons 1 and 2 on your new remote control. Keep them pressed until the LED light on the receiver turns ON solid (stops flashing). Release the buttons.
  4. Pair Additional Buttons: Press button 1 on your new remote control until the LED on the receiver starts flashing again. Repeat this step for any other buttons you wish to program on the remote. Each button on the remote can be programmed to control a different function or door.
Diagram of a Clonix 2 Receiver board, showing the location of SW1, SW2 buttons, and the LED indicator, essential for programming.
Figure 7: Clonix 2 Receiver Board (Example for programming)

If you encounter difficulties, please refer to the "Troubleshooting" section or contact customer support.

Video 1: Programming demonstration for BFT remote controls.

6. Operasyon

Once programmed, operating your BFT remote control is simple:

  • Açılış/Kapanış: Press the programmed button on your remote control to activate your garage door or gate opener.
  • Durdurma: Press the same button again while the door/gate is in motion to stop it.
  • Geri gitme: Depending on your opener's settings, pressing the button again after stopping may reverse the direction of travel.
A single BFT 4-button remote control, labeled '1 PCS'.
Figure 8: BFT 4-button remote control
A single BFT 2-button remote control, labeled '1 PCS'.
Figure 9: BFT 2-button remote control

7. Bakım

Pil Değişimi:

Your remote control comes with a pre-installed battery. When the remote's range decreases significantly or the LED indicator on the remote no longer lights up when a button is pressed, it's likely time to replace the battery. The remote uses a standard 12V battery (e.g., 23A or A23 type).

  1. Uzaktan kumandayı dikkatlice açın.asing.
  2. Eski pili çıkarın.
  3. Yeni bir 12V pili, doğru kutuplara (+/-) dikkat ederek takın.
  4. Uzaktan kumandayı kapatın.asing güvenli bir şekilde.

8. Sorun Giderme

  • Programlamadan sonra uzaktan kumanda çalışmıyor:
    • Ensure you followed all programming steps correctly.
    • Check if the receiver's LED lit up solid during programming.
    • Verify that your remote model is indeed compatible with your receiver.
    • Uzaktan kumandanın pilini kontrol edin.
  • Azaltılmış çalışma aralığı:
    • Uzaktan kumandanın pilini değiştirin.
    • Ensure there are no new obstructions (e.g., metal objects, large vehicles) between the remote and the receiver.
    • Bölgedeki radyo paraziti kaynaklarını kontrol edin.
  • Receiver LED does not flash when SW1/SW2 is pressed:
    • Ensure the receiver has power.
    • Consult your receiver's specific manual for troubleshooting its programming mode.

9. Kullanıcı İpuçları

  • If you are having trouble with programming, search for a video tutorial specific to your BFT receiver model. Many users find visual guides helpful.
  • Always keep a spare remote or ensure you have access to your receiver's programming buttons in case your primary remote is lost or damaged.

10. Sıkça Sorulan Sorular

Q: Can I program this remote without accessing my receiver?
A: No, programming requires physical access to the receiver unit to press its programming buttons (SW1 or SW2).
Q: Is there a programming video available?
A: Yes, a programming video is embedded in the "Setup and Programming" section of this manual. If you need further assistance, please contact customer support.

11. Garanti ve Destek

For any issues not covered in this manual, or for further assistance, please contact the seller or manufacturer's customer support. Keep your purchase records for warranty purposes.

PDF formatında bir kullanıcı kılavuzu da indirilebilir: View Kullanım Kılavuzu (PDF)

İlgili Belgeler - Mitto B RCB02 R1, RCB04 R2, MITTO 2, 4, MITTO2A, MITTO4A, KLEIO B RCA 02/04

Önview BFT Remote Control Programming Instructions for RCB Receivers
Step-by-step guide for programming BFT MITTO and KLEIO rolling code remote controls with BFT RCB02 and RCB04 receivers. Includes procedures for Type 1 and Type 2 receiver models.
Önview BFT Clonix 2 Receiver Alpha Control Panel Programming Guide
Step-by-step instructions for programming the BFT Clonix 2 Receiver Alpha Control Panel. Learn how to pair your remote controls with the receiver using the SW1 and SW2 buttons.
Önview BFT CLONIX1-2 ve MITTO 2-4 433MHz Radyo Kontrol Sistemi Kurulum Kılavuzu
BFT CLONIX1-2 alıcı ve MITTO 2-4 433MHz radyo kontrol vericileri için kapsamlı kurulum kılavuzu; programlama, klonlama, güvenlik ve kapı ve geçit otomasyonu için teknik özellikler konularını kapsamaktadır.
Önview BFT Mitto 2M/4M Uzaktan Kodlama Talimatları: Kapsamlı Bir Kılavuz
Garaj ve kapı açıcılarınız için BFT Mitto 2M ve 4M uzaktan kumandalarınızı nasıl programlayacağınızı öğrenin. Bu kılavuz, dijital ekranlı ve ekransız alıcılar için kodlamayı ve önemli güvenlik uyarılarını kapsar.
Önview BFT MITTO COOL Uzaktan Kumandalar - Programlama, Güvenlik ve Uygunluk Beyanı
BFT MITTO COOL C4, C2 ve STYLE C4 uzaktan kumandaları için kapsamlı kılavuz; programlama adımları, temel pil güvenliği uyarıları, teknik özellikler ve AB Uy conformity Beyanı'nı kapsamaktadır.
Önview BFT MITTO 2B Uzaktan Kumanda Kodlama Talimatları | Retro Uzaktan Kumandalar
Mevcut uzaktan kumanda ve alıcı LCD ekran yöntemlerini kapsayan, kapı açıcılar için BFT MITTO 2B uzaktan kumandalarının kodlanmasına yönelik adım adım kılavuz. Sorun giderme ipuçları da içerir.