KUGOO M2 Pro Electric Scooter Dashboard & Controller User Manual

1. Giriş

This manual provides essential information for the safe and proper installation, operation, and maintenance of your KUGOO M2 Pro Electric Scooter Dashboard and Motor Controller. Please read this manual thoroughly before attempting any installation or use.

Ürün Açıklaması

The Controller is the central electronic processing unit of your electric scooter. It regulates power delivery from the battery to the motor based on input from the throttle, brake sensors, and other components, controlling speed, acceleration, and braking regeneration.

The Dashboard serves as the monitor display, providing essential information to the rider.

Image: KUGOO M2 Pro Dashboard and Controller units with their respective wiring harnesses.

2. Güvenlik Bilgileri

⚠ ATTENTION: Always prioritize safety. Failure to follow these instructions may result in injury, damage to the product, or voiding of warranty.

• Protective equipment should be worn when operating the electric scooter.
• Trafikte kullanılmamalıdır.
• Sadece ev içi kullanıma uygundur.
• 36 aydan küçük çocuklar için uygun değildir.

Kullanım Sınırlamaları

• Cilttage & Current Rating: This controller is designed for a specific voltage (e.g., 36V, 48V) and current rating. Never connect it to a battery with a different voltage, as this can cause immediate and catastrophic failure, fire, or explosion.
• Motor Uyumluluğu: It must be used only with a brushless DC (BLDC) hub motor whose specifications (phase, hall sensor configuration) are compatible with the controller.
• Thermal Limits: The controller has operational temperature limits. Avoid continuous high-load operation (e.g., climbing long, steep hills) which may cause overheating and automatic shutdown or permanent damage. Ensure it is installed in a location with adequate ventilation.
• Moisture & Environment: This component is not waterproof unless specified with a certified IP rating. It must be protected from direct exposure to water, rain, snow, and high humidity. Do not install it in areas prone to splashing or submersion.
• Modification Prohibited: Do not attempt to modify, reprogram ("tune"), or bypass any safety limits of the controller. Doing so voids any warranty, can damage the motor and battery, and significantly increases the risk of accident or fire.

3. Kurulum ve Bağlantı

3.1. Preparation (Safety First)

1. Ensure the scooter is completely powered off and the battery is disconnected.
2. Wait at least 5 minutes after disconnection to allow any residual current to dissipate.

3.2. Kontrol Cihazının Montajı

Securely mount the controller inside the scooter's deck or designated compartment using the provided screws or mounting brackets. Ensure it does not contact sharp edges, moving parts, or the battery. The metal heat sink (if present) should face an open area for airflow.

Image: KUGOO M2 Pro Controller unit, showing various wire connections.

3.3. Kablolama Bağlantısı

Connect all cables in the following order, ensuring each connector is fully seated and locked:

1. Pil: Connect the main power cables from the battery to the controller's battery input terminals, observing correct polarity (RED to Positive (+), BLACK to Negative (-)). Incorrect connection will destroy the controller.
2. Motor: Connect the three thick phase wires (usually Yellow, Green, Blue) and the thinner hall sensor wires (5-pin connector) from the motor to the corresponding ports on the controller.
3. Throttle, Brake Levers, Display: Connect the throttle, brake sensor, and dashboard/display unit cables to their designated ports.

Resim: Üst view of the KUGOO M2 Pro Controller, illustrating the various wiring connections.

Image: KUGOO M2 Pro Dashboard unit, which connects to the controller.

4. Operasyon

4.1. Final Check & Power-On

1. Double-check all connections for correctness and security. Ensure no wires are pinched.
2. Aküyü tekrar bağlayın.
3. Scooter'ı açın. Do not apply throttle yet.
4. Listen for any unusual sounds from the controller or motor.

4.2. İlk Test

1. With the scooter lifted off the ground, gently apply the throttle.
2. Observe if the motor spins smoothly and in the correct direction.
3. If the wheel spins backward, power off and swap any two of the three motor phase wire connections on the controller. Test again.
4. Confirm that the brake levers cut motor power as intended.

5. Bakım

To ensure the longevity and optimal performance of your KUGOO M2 Pro Dashboard and Controller, follow these general maintenance guidelines:

• Regularly inspect all wiring connections for signs of wear, corrosion, or looseness.
• Keep the controller and dashboard clean and free from dust, dirt, and moisture.
• Aşırı ısınmayı önlemek için kontrol ünitesinin çevresinde yeterli havalandırma olduğundan emin olun.
• Bileşenleri uzun süre aşırı sıcaklıklara veya doğrudan güneş ışığına maruz bırakmaktan kaçının.
• Temizlik için sert kimyasallar veya aşındırıcı malzemeler kullanmayın.

6. Sorun Giderme

7. Özellikler

Based on the "Sensorless Motor Control" label visible on the controller:

Resim: Yakın çekim view of the controller's label, detailing model, voltage, güç ve akım özellikleri.

8. Kullanıcı İpuçları

• Uyumluluk Kontrolü: Satın almadan önceasing or installing, always verify that the replacement controller and dashboard are fully compatible with your specific KUGOO M2 Pro model, especially regarding voltage, motor type, and display connections. If you are replacing only one component (e.g., controller), ensure it works seamlessly with your existing original display.
• Profesyonel Kurulum: If you are unsure about any step of the installation process, it is highly recommended to seek assistance from a qualified technician to avoid damage to the components or the scooter.

9. Garanti ve Destek

For warranty information, technical support, or further assistance, please refer to the official KUGOO support channels or contact your retailer.

A detailed user manual in PDF format may be available for download from the manufacturer's website or through the retailer. (Reference: Kullanım kılavuzu (PDF))