Aoxun 14' x 10' Lean-to Gazebo Pergola Instruction Manual

Important Reminders Before You Begin

• The gazebo comes in 2 boxes. If anything is missing, contact us for assistance.
• Install the gazebo against a wall for maximum stability.
• When installing, align screws within a section with the corresponding holes before tightening them all.

Kurulum ve Montaj

1. Pillar Installation

Begin by assembling the pillars. Ensure all parts are complete and undamaged before starting. Refrain from tightening screws fully until all components are aligned to allow for adjustments.

Ensure that the screw holes on both sides are facing the same direction for proper alignment.

2. Beam Installation

Proceed with the beam installation. Similar to the pillars, insert all screws before tightening to facilitate alignment. Once all screws are in place, tighten them securely.

3. Beam-to-Column Connection

Connect the assembled beams to the columns. Again, refrain from tightening screws initially to ensure all holes align correctly. Once aligned, tighten all screws.

For easier installation, flip the assembly upside down when connecting the beams to the columns.

4. Ridge Beam Assembly

Assemble the ridge beam components. Ensure the two triangular pieces are facing the same direction for correct installation. Tighten all four nuts securely.

Connect the slightly narrower side of the component to the pipe.

5. Roof Panel Installation

When installing the roof panels, note that Part G has a water leakage hole. This hole should be installed facing upwards to ensure proper drainage.

Remove any protective stickers from the panels during installation.

6. Front Beam Installation

Install the front beam to complete the main structure. Ensure all connections are secure.

7. Duvara Montaj

The gazebo must be wall-mounted using expansion bolts for stability. Drill holes into the wall and secure the brackets firmly. This step is crucial for the gazebo's load-bearing capacity and resistance to weather conditions.

Çardakınızı Çalıştırmak

The Aoxun Lean-to Gazebo Pergola is designed for versatile outdoor use, providing shade and weather protection. Its polycarbonate top reflects 99% of UV rays, offering excellent sun protection. The sloped roof and gap drainage system ensure efficient water runoff, making it suitable for various weather conditions.

The structure is built with carbon steel frames and a triangular metal design for durability and stability. It is designed to withstand a maximum wind resistant grade of 7 (31-38 mph) and a maximum snow loading depth of 4 inches when properly installed with ground nails and expansion bolts.

Bakım

• Düzenli Temizlik: Clean the polycarbonate roof panels and metal frame periodically with mild soap and water. Avoid abrasive cleaners or tools that could scratch the surfaces.
• Bağlantı Elemanlarını Kontrol Edin: Annually inspect all screws and bolts to ensure they remain tight and secure. Re-tighten any loose fasteners to maintain structural integrity.
• Drenaj sistemi: Ensure the gap drainage system is clear of debris (leaves, dirt) to allow for proper water runoff. Clogged drainage can lead to water accumulation.
• Kar Temizleme: While the gazebo can tolerate up to 4 inches of snow, it is recommended to remove heavy snow accumulation promptly to prevent excessive stress on the structure.
• Rüzgar Koruması: In areas prone to high winds, consider additional anchoring or temporary disassembly during severe weather conditions to prevent damage.

Sorun giderme

• Sorun: Çatıda su birikmesi.

  Çözüm: Check the drainage gaps for any blockages and clear them. Ensure the roof panels are correctly installed with the leakage hole facing upwards as per instructions.

• Sorun: Çardak dengesiz veya sallanıyor gibi hissediliyor.

  Çözüm: Verify that all wall-mounting expansion bolts and other fasteners are securely tightened. Ensure the gazebo is installed on a flat, level surface. If necessary, re-anchor the structure.
• Sorun: Montaj sırasında vida deliklerinin hizalanmasında zorluk.

  Çözüm: Do not fully tighten any screws until all components for a section are loosely assembled. This allows for minor adjustments to align holes. Once all screws are in place, tighten them gradually and evenly.

Özellikler

Garanti ve Destek

For any missing parts, assembly assistance, or warranty inquiries, please contact Aoxun customer support. Refer to your purchase documentation for specific warranty terms and contact details.

Üretici: Aoxun

İade politikasi: 30-day refund/replacement policy (check with retailer for full details).