BoxWave ClearTouch Crystal Screen Protector for Autophix 1100 Instruction Manual

1. Giriş

This manual provides instructions for the proper installation, usage, and maintenance of your BoxWave ClearTouch Crystal Screen Protector for the Autophix 1100 device. Please read these instructions carefully before proceeding with installation.

Paket İçeriği

• Two (2) ClearTouch Crystal Screen Protectors
• One (1) ClearTouch Applicator Card
• One (1) Microfiber Cleaning Cloth
• One (1) Dust Removing Sticker

Ürün Özellikleri

• Netlik: Provides 99% visual transparency for vibrant color display.
• Koruma: Shields your device screen from scratches and dust.
• Hassas Uyum: Custom-cut to match the exact dimensions of the Autophix 1100.
• Residue-Free: Utilizes a glueless adhesive that leaves no sticky residue upon removal.

2. Kurulum Kılavuzu

Follow these steps carefully to ensure a smooth and bubble-free installation of your screen protector.

1. Cihazınızın Ekranını Temizleyin: Use the provided microfiber cleaning cloth to thoroughly clean the screen of your Autophix 1100. Ensure all dust, fingerprints, and smudges are removed. For stubborn marks, a screen cleaner (not included) can be used sparingly.
2. Tozu Temizleyin: Use the dust removing sticker to lift any remaining dust particles from the screen. Lightly dab the sticker across the screen surface.
3. Peel Back Layer 1: Carefully peel back the protective layer labeled '1' from one end of the screen protector. Avoid touching the adhesive side.
4. Hizala ve Uygula: Align the exposed adhesive edge of the screen protector with one edge of your device screen. Once aligned, slowly and steadily lower the rest of the screen protector onto the device, peeling back layer '1' as you go.
5. Kabarcıkları Düzeltin: Use the applicator card to gently push out any air bubbles towards the edges of the screen protector. Start from the center and work your way outwards.
6. Remove Layer 2: Once the screen protector is applied and most bubbles are removed, carefully peel off the top protective layer labeled '2'.
7. Final Smoothing: Perform a final pass with the microfiber cloth to remove any remaining small bubbles or smudges on the surface of the newly applied protector.

Not: The special low-tack adhesive may take up to 2 days of regular use to fully adhere around the edges, allowing any small air gaps to clear out naturally.

3. Kullanım ve Bakım

Genel Kullanım

The ClearTouch Crystal screen protector is designed to maintain the original touch sensitivity and display clarity of your Autophix 1100. Operate your device as usual.

Temizlik ve Bakım

To clean your screen protector, gently wipe it with the provided microfiber cleaning cloth. For more thorough cleaning, dampen the cloth slightly with water or a screen-safe cleaning solution. Avoid harsh chemicals or abrasive materials, as these can damage the protector's surface.

4. Sorun Giderme

• Montaj Sonrası Oluşan Kabarcıklar: Small bubbles are common immediately after installation. Use the applicator card to push them towards the nearest edge. For very small bubbles, allow 24-48 hours for them to dissipate naturally as the adhesive fully cures.
• Dust Under Protector: If dust particles are trapped under the protector, carefully lift the nearest corner of the protector with a piece of tape, use the dust removing sticker to lift the particle, and then reapply the protector.
• Hizalama hatası: If the protector is significantly misaligned, you may carefully peel it off, clean both the device screen and the protector (if no dust has adhered to the adhesive side), and attempt reinstallation. The ClearTouch Crystal is designed for reusability and installation forgiveness.

5. Ürün Özellikleri

6. Destek Bilgileri

For further assistance, technical support, or warranty inquiries regarding your BoxWave ClearTouch Crystal Screen Protector, please contact BoxWave Corporation directly.

Üretici: BoxWave Şirketi
Webalan: www.boxwave.com (Lütfen yetkiliye başvurun.) web(En güncel iletişim bilgileri için lütfen siteyi ziyaret edin.)

Please have your product model (Autophix 1100) and purchase details ready when contacting support.