BSEED N020-120-1P

BSEED N020-120V-30A Surge Protector User Manual

Model: N020-120-1P

1. Giriş

The BSEED N020-120V-30A Surge Protector is a heavy-duty voltage regulator designed to protect your valuable home appliances from electrical fluctuations. It safeguards against high and low voltage, brownouts, spikes, instant surges, power failures, and load shedding. This device is suitable for a wide range of appliances, including refrigerators, air conditioners, TVs, computers, and other household electronics operating at 120V and up to 30A (3600W).

2. Güvenlik Talimatları

Please read and understand all safety instructions before installing or operating this surge protector. Failure to follow these instructions may result in electric shock, fire, or damage to the product or connected appliances.

  • Elektrik Tehlikesi: Ensure the power supply is disconnected before installation or making any adjustments.
  • Doğru Kablolama: Always ensure the correct polarity of the cables (phase, neutral, grounding) during connection. Refer to the connection diagram for proper wiring.
  • Anma Kapasitesi: Do not exceed the maximum current capacity of 30 Amps or 3600 Watts. Overloading can cause damage and fire hazards.
  • Sadece İç Mekanda Kullanım: This device is intended for indoor use in dry locations. Do not expose to water or excessive humidity.
  • Güvenli Bağlantılar: Ensure all wire connections are tight and secure to prevent arcing or overheating.
  • Profesyonel Kurulum: Kurulum süreci konusunda emin değilseniz, yetkili bir elektrikçiye danışın.
Connection Diagram for BSEED N020-120V-30A Surge Protector
Şekil 2.1: Connection Diagram. This diagram illustrates the proper wiring for the surge protector, showing connections for electric supply, short circuit protector, and the equipment to be protected. Pay close attention to phase, neutral, and grounding connections for safety.

3. Ürün Bittiview ve Özellikler

3.1 Temel Bileşenler ve Göstergeler

Basic Characteristics of BSEED N020-120V-30A Surge Protector
Şekil 3.1: Basic Characteristics. This image highlights the indicator lights on the surge protector: 1. Normal Voltage (Green), 2. Over Voltage (Orange), and 3. Low Voltage (Red). It also shows the adjustable voltage settings and reconnection delay.
  • Indicator of NORMAL voltage (Green): Illuminates when the voltage, güvenli çalışma aralığındadır.
  • Indicator of OVER voltage (Orange): Illuminates when the input voltage exceeds the set maximum threshold.
  • Indicator of LOW voltage (Red): Illuminates when the input voltage drops below the set minimum threshold.
  • Ayarlanabilir Hacimtage Ayarlar: Dials for setting minimum (Under Voltage Cut-off) and maximum (Over Voltage Cut-off) voltage eşikler.
  • Adjustable Reconnection Delay: Dial for setting the waiting time before power is reconnected after a voltagolay.

3.2 Gelişmiş Özellik

Other Novel Features of BSEED N020-120V-30A Surge Protector
Şekil 3.2: Other Novel Features. This diagram illustrates the internal components and features, including adjustable voltage and delay settings, manual ON/OFF switch, assembly facilities, safer connectors with protective covers, convenient access for gutters, and a protective cover with safety seal holes.
  1. Adjustable LOW voltagizin verildi: 90V ile 115V arasında seçilebilir.
  2. Adjustable OVER voltagizin verildi: 125V ile 145V arasında seçilebilir.
  3. Adjustable waiting cycle: Between 180-300 seconds (3 to 5 minutes).
  4. Manual ON and OFF switch: For convenient control.
  5. Assembly facilities: Two (2) options for mounting on a 2"x4" box or a flat surface.
  6. Safer connectors: Giriş ve çıkış terminalleri bir kapakla korunmaktadır.
  7. Convenient access for gutters: Through predictable sections.
  8. Protective cover with safety seal holes: To prevent unauthorized manipulation of adjustments and connections.

3.3 Ürün Boyutları

Dimensions of BSEED N020-120V-30A Surge Protector
Şekil 3.3: Product Dimensions. The surge protector measures approximately 3.50 inches in height, 4.60 inches in width, and 1.45 inches in depth.

4. Kurulum

4.1 Kablolama Şeması

Başvurun Figure 2.1 (Connection Diagram) in the Safety Instructions section for detailed wiring instructions. Ensure all connections are made correctly, matching phase (L), neutral (N), and grounding (G) wires from your electric supply to the protector's input terminals, and then from the protector's output terminals to your appliance.

4.2 Montaj

The surge protector can be mounted in two ways:

  • On a 2"x4" electrical box: Use the designated assembly facilities on the device.
  • Düz bir yüzeyde: Secure the device using appropriate screws through the provided mounting holes.

4.3 İlk Kurulum ve Ayarlamalar

Before connecting your appliance, you can adjust the voltage cut-off points and the delay time:

  • Cilt Altındatage Kesinti: Use the 'MINIMUM V-' dial to set the lowest acceptable voltage 90V ile 115V arasında.
  • Aşırı Hacimtage Kesinti: Use the 'MAXIMUM V+' dial to set the highest acceptable voltage 125V ile 145V arasında.
  • Reconnection Delay: Use the 'RECONNECTION S' dial to set the waiting period (3 to 5 minutes) before power is restored after a voltagolay.

It is recommended to set these values according to the specifications of the appliance you intend to protect and your local power grid stability.

5. Operasyon

5.1 Açma

After proper installation and adjustment:

  1. Ensure the manual ON/OFF switch is in the 'ON' position.
  2. Apply power to the surge protector.
  3. The device will initiate a delay cycle (3 to 5 minutes, as set). During this time, the indicator lights may show a waiting state.
  4. Once the delay period is complete and the voltage is stable within the set parameters, the green 'NORMAL' indicator light will turn on, and power will be supplied to your connected appliance.

5.2 Gösterge Işığı

  • Green Light (NORMAL): vol olduğunu gösterirtage is stable and within the safe operating range, and power is being supplied to the appliance.
  • Orange Light (OVER VOLTAGE): Indicates that the input voltage is too high. The protector has cut off power to safeguard the appliance. Power will be restored after the voltage normalizes and the delay cycle completes.
  • Red Light (LOW VOLTAGE): Indicates that the input voltage is too low. The protector has cut off power to safeguard the appliance. Power will be restored after the voltage normalizes and the delay cycle completes.

5.3 Tipik Uygulamalar

BSEED N020-120V-30A Surge Protector in various applications
Şekil 5.1: Typical Applications. The BSEED N020-120V-30A Surge Protector is suitable for protecting a variety of heavy-duty home appliances, including air conditioners, washing machines, rice cookers, and microwave ovens.

6. Bakım

The BSEED N020-120V-30A Surge Protector requires minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:

  • Temizlik: Periodically wipe the exterior of the device with a soft, dry cloth. Do not use liquid cleaners or solvents.
  • Bağlantı Kontrolü: Annually inspect all wiring connections to ensure they remain tight and free from corrosion.
  • Çevresel Koşullar: Ensure the device is kept in a dry, well-ventilated area, away from direct sunlight, heat sources, and corrosive environments.
  • Koruyucu Kılıf: Keep the protective cover securely closed to prevent dust and unauthorized access to internal components.

7. Sorun Giderme

Eğer aşırı gerilim koruyucunuzla ilgili sorunlar yaşıyorsanız, aşağıdaki yaygın sorunlar ve çözümlere göz atın:

SorunOlası NedenÇözüm
Appliance does not power on after connecting.1. Surge protector is in delay cycle.
2. Giriş hacmitage is outside safe range.
3. Manual switch is OFF.
4. Gevşek kablo bağlantısı.
1. Wait for the set delay time (3-5 minutes).
2. Check indicator lights (Orange for Over, Red for Low). Wait for voltage normalleştirmek için.
3. Ensure the manual ON/OFF switch is in the 'ON' position.
4. Disconnect power and check all wiring connections for tightness.
Orange (Over Voltage) or Red (Low Voltage) light remains on.Persistent unstable voltage güç kaynağından.The protector is functioning as intended by cutting off power. If the issue persists, contact your electricity provider or a qualified electrician to check your home's electrical system.
Device appears to be non-functional.Internal fault or severe damage.Disconnect from power immediately. Do not attempt to repair. Contact BSEED customer support for assistance.

8. Teknik Özellikler

ŞartnameDeğer
MarkaBEZİ
Model NumarasıN020-120-1P
Cilttage120V AC
Maksimum Akım30 Amps
Maksimum Güç3600 Watt
Cilt Altındatage Cut-off RangeAdjustable 90V - 115V
Aşırı Hacimtage Cut-off RangeAdjustable 125V - 145V
Reconnection Delay TimeAdjustable 3 - 5 minutes (180-300 seconds)
Mağaza Sayısı1
Fiş TipiB Tipi - 3 pimli (Kuzey Amerika)
Uyumlu CihazlarAir Conditioner, Computer, House Electric Appliances, Refrigerator, Television
Muhafaza MalzemesiAluminum, Copper, Polycarbonate, Rubber
Özel ÖzelliklerAyarlanabilir Hacimtage, Surge Protection, Manual ON/OFF Switch

9. İletişim ve Destek

For further assistance, technical support, or warranty inquiries, please contact BSEED customer service through the retailer where the product was purchased or visit the official BSEED webalan.

Üretici: BEZİ

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.