TCE ATH810002U-1 Torin 10 Ton Çift Pistonlu Düşük Profillifile Şişe Krikosu Kullanım Kılavuzu

giriiş

This manual provides essential instructions for the safe operation, maintenance, and troubleshooting of your TCE ATH810002U-1 Torin 10-Ton Double Ram Low Profile Bottle Jack. Please read and understand all instructions and warnings before using this product. Proper use and maintenance will ensure optimal performance and extend the lifespan of your jack.

Image: The TCE ATH810002U-1 Torin 10-Ton Double Ram Low Profile Bottle Jack, shown with its handle components.

Güvenlik Bilgileri

UYARI: Bu uyarılara uyulmaması, kişisel yaralanmalara ve/veya maddi hasara neden olabilir.

• Always read and understand the entire manual before operating the jack.
• 10 ton (20,000 lbs) olan nominal taşıma kapasitesini aşmayın.
• Use the jack only on a hard, level surface.
• Always use jack stands to support the load immediately after lifting. Do not rely solely on the jack to support the load.
• Ensure the load is centered on the jack saddle.
• Do not work under a lifted load unless it is properly supported by jack stands.
• Keep hands and feet clear of the jack and the load during lifting and lowering.
• Güvenlik gözlüğü ve eldiven gibi uygun kişisel koruyucu ekipman (KKD) kullanın.
• Never modify the jack or use it for purposes other than its intended use.
• Inspect the jack before each use for any signs of damage, leaks, or wear. Do not use a damaged jack.
• Yükü yavaşça ve kontrollü bir şekilde indirin.

Ürün Özellikleri

The TCE ATH810002U-1 bottle jack incorporates several design elements for enhanced performance and durability:

• Double Ram Design: Provides extended lift travel, allowing for both a lower retracted height and a higher extended height.
• Ultra Düşük Profesyonelfile: Retracted height of 4.92 inches, suitable for vehicles with low ground clearance.
• Anti-Skid Saddle: A serrated, heat-treated saddle ensures a secure grip on the load.
• Upgraded Piston: Designed for reliable and efficient lifting.
• Dayanıklı Yapı: Engineered with drop-forged alloyed steel and robotic welding for quality and durability. Features powder coating for resistance to moisture and chemicals.
• Special Hydraulic Oil: Functions normally in temperatures from -13°F to 140°F, offering thermal stability and abrasion resistance.

Resim: Ayrıntılı view highlighting the well-polished double ram, anti-skid saddle, and upgraded piston components of the jack.

Image: Visual representation of the manufacturing quality, including robotic welding, powder coating, heavy-duty steel construction, and the ergonomic design for easy lifting.

Kurmak

1. Paketin açılması: Carefully remove the jack and all components from the packaging. Inspect for any shipping damage.
2. Kol Montajı: Insert the handle sections together to form the complete operating handle.
3. Hava Tahliyesi (Boşaltma): Before first use, or if the jack has been stored for a long time, it may be necessary to purge air from the hydraulic system.
   • Turn the release valve counter-clockwise one full turn to open it.
   • Pump the handle 5-6 full strokes.
   • Kapatmak için tahliye vanasını saat yönünde çevirin.
   • The jack should now operate smoothly. If not, repeat the process.
4. Atama: Position the jack on a firm, level surface directly under the lifting point of the load as specified by the load manufacturer.

Kullanım Talimatları

Yükü Kaldırmak:

1. Ensure the jack is on a hard, level surface and the load is stable.
2. Close the release valve firmly by turning it clockwise until tight. Do not overtighten.
3. Insert the handle into the pump socket.
4. Pump the handle up and down to raise the jack saddle until it makes contact with the lifting point of the load.
5. Continue pumping the handle to lift the load to the desired height.
6. Immediately after lifting, place appropriately rated jack stands under the load at designated support points.
7. Slowly lower the load onto the jack stands by gently turning the release valve counter-clockwise.

Yükün İndirilmesi:

1. Ensure the area around the load is clear.
2. If the load is on jack stands, slightly raise the load off the jack stands using the jack.
3. Kriko ayaklarını çıkarın.
4. Slowly and carefully turn the release valve counter-clockwise to lower the load. Control the lowering speed by adjusting how much you open the valve.
5. Once the load is fully lowered, remove the jack.

Bakım

Regular maintenance is crucial for the safe and efficient operation of your hydraulic jack.

• Yağlama: Periodically lubricate moving parts with light machine oil.
• Hidrolik Yağ Seviyesi: Check the hydraulic oil level every three months.
  • With the jack fully lowered, remove the oil filler plug.
  • The oil level should be just below the filler hole.
  • If low, add high-quality hydraulic jack oil (e.g., ISO VG 15 or equivalent) until the correct level is reached. Do not overfill.
  • Doldurma tapasını değiştirin.
• Temizlik: Krikoyu temiz tutun ve kir, yağ ve aşındırıcı maddelerden arındırın.
• Depolamak: Store the jack in a fully lowered position in a dry, protected area.
• Denetleme: Before each use, inspect for cracks, bends, leaks, or any other damage. Do not use if damaged.

Image: Illustration detailing the operating temperature range of the special hydraulic oil used in the jack, from -13°F to 140°F, highlighting its thermal stability and abrasion resistance.

Sorun giderme

Özellikler

Image: Visual representation of the jack's minimum retracted height (4.92 inches) and maximum extended height (8.46 inches).

Garanti ve Destek

This TCE ATH810002U-1 Torin Bottle Jack comes with a 2 yıllık sınırlı üretici garantisi. For warranty claims, technical support, or to inquire about replacement parts, please contact TCE customer service. Keep your purchase receipt as proof of purchase.

For further assistance, please refer to the official TCE websiteyi ziyaret edin veya müşteri destek kanallarıyla iletişime geçin.