giriiş
The Behringer CLOCKED SEQUENTIAL CONTROL MODULE 1027 is a faithful reproduction of the legendary 2500 Series 8-position step sequencer. Designed for Eurorack systems, this module provides precise control over voltage and gate signals, making it an essential tool for creating complex melodic and rhythmic patterns in your modular synthesizer setup. Its robust design and intuitive interface ensure reliable performance and creative flexibility.
Önemli Güvenlik Talimatları
- Read these instructions thoroughly before operating the module.
- Bu talimatları ileride başvurmak üzere saklayın.
- Ürün üzerinde ve kılavuzda yer alan tüm uyarıları dikkate alın.
- Güvenli kullanım için tüm talimatları izleyin.
- Bu cihazı su veya nem yakınında kullanmayın.
- Sadece kuru bezle temizleyin.
- Hiçbir havalandırma açıklığını kapatmayın. Üreticinin talimatlarına uygun şekilde kurulum yapın.
- Radyatörler, kalorifer ızgaraları, sobalar veya diğer cihazlar (dahil) gibi herhangi bir ısı kaynağının yakınına kurmayın. amp(ısı üreten)
- Sadece üretici tarafından belirtilen aparatları/aksesuarları kullanın.
- Tüm servis işlemleri için kalifiye servis personeline başvurun. Cihaz herhangi bir şekilde hasar gördüğünde servis gereklidir.
Kurmak
Eurorack Kurulumu
The CLOCKED SEQUENTIAL CONTROL MODULE 1027 is designed for installation into a standard Eurorack case. Ensure your Eurorack case has sufficient power and space (16 HP width) before installation.
- Kapat: Always disconnect power from your Eurorack case before installing or removing any modules.
- Montaj: Align the module with an available 16 HP space in your Eurorack case. Secure it using the provided screws.
- Güç Bağlantısı: Connect the 16-pin power cable from your Eurorack power supply to the module's power header. Ensure the red stripe on the cable aligns with the -12V pin on both the module and the power supply. Incorrect connection can damage the module and/or power supply.
- Güç Açık: Once securely mounted and connected, you can power on your Eurorack case.
Şekil 1: Ön view of the Behringer 1027 module, showing all controls and patch points. This image illustrates the module's layout for proper installation and connection within a Eurorack system.
İlk Bağlantılar
To begin using the 1027, connect its outputs to other modules in your Eurorack system. Common connections include:
- Clock Input (CLK IN): Connect a clock signal from another module (e.g., an LFO or clock divider) to the CLK IN jack to drive the sequencer.
- CV Outputs (CH A, CH B, CH C): Patch these outputs to the CV inputs of oscillators, filters, or other modules to control pitch, cutoff, or other parameters.
- Gate Outputs (POSITION GATES 1-8): Connect these to gate inputs of envelope generators or drum modules to trigger events at specific steps.
Şekil 2: Yakın çekim view of the input and output jacks on the Behringer 1027 module, highlighting the various patch points for integration into a modular system.
Kullanım Talimatları
Üzerindeview Kontrollerin
The 1027 module features a clear layout of controls for intuitive sequencing:
- ORAN Düğmesi: Adjusts the speed of the internal clock. The range switch (LOW/HIGH) selects the clock speed range.
- PULSE WIDTH Knob: Controls the width of the gate pulses. The switch (INT/EXT) selects between internal control or external CV control.
- Açma / kapama düğmesi: Toggles the sequencer's operation.
- STEP Buttons (1-8): Each step has a corresponding button to activate/deactivate it.
- CV Knobs (A, B, C for each step): Adjust the control voltage output for each of the three channels (A, B, C) at each step.
- POSITION GATES (1-8): Individual gate outputs for each step.
- STEP/RESET Buttons: Manual step advance and reset functions.
Şekil 3: Açısal view of the Behringer 1027 module, providing a clear perspective of the control knobs and buttons for each step and channel.
Creating a Sequence
- Saati ayarla: Kullanın ORAN topuz ve DÜŞÜK/YÜKSEK switch to set the desired tempo. Alternatively, connect an external clock to the CLK GİRİŞİ kriko.
- Activate Steps: Basın ADIM buttons (1-8) to activate the desired number of steps in your sequence. Active steps will typically illuminate.
- Adjust CV: For each active step, turn the CV Knobs (A, B, C) ses seviyesini ayarlamak içintage level for each channel. These voltages will be outputted sequentially.
- Configure Gates: The KONUM KAPILARI will output a pulse when their corresponding step is active. Use these to trigger envelopes or other events.
- Başlat/Durdur: Kullanın AÇIK/KAPALI switch to start and stop the sequence.
Gelişmiş Özellikler
- External Pulse Width Control: Connect a CV source to the EXT input for the PULSE WIDTH section to dynamically control the gate pulse width.
- Manual Step/Reset: The ADIM Ve SIFIRLAMA buttons allow for manual control over the sequence progression, useful for live performance or precise programming.
Bakım
Temizlik
To maintain the appearance and functionality of your module:
- Always power off your Eurorack system before cleaning.
- Use a soft, dry, lint-free cloth to wipe the module's surface.
- İnatçı kirler için hafifçeampBezi suyla yıkayın. Sert kimyasallar veya aşındırıcı temizleyiciler kullanmaktan kaçının.
- Do not allow any liquids to enter the module through jacks or openings.
Depolamak
When not in use for extended periods, store the module in a cool, dry place, away from direct sunlight and extreme temperatures. If removed from the Eurorack case, store it in anti-static packaging.
Sorun giderme
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Modül açılmıyor. | Incorrect power cable connection; Eurorack power supply off or faulty. | Check power cable orientation (red stripe to -12V). Ensure Eurorack power supply is on and functioning correctly. |
| Sequencer not advancing steps. | No clock signal; ON/OFF switch is OFF; RATE knob set too low. | Connect a clock signal to CLK IN. Ensure ON/OFF switch is ON. Increase the RATE knob setting. |
| No CV output from a channel. | CV knob for that step/channel is at minimum; step is not active. | Adjust the corresponding CV knob. Ensure the step is active (illuminated). |
| No Gate output from a position. | Step is not active; PULSE WIDTH set to minimum. | Ensure the step is active. Increase the PULSE WIDTH setting. |
Özellikler
| Özellik | Detay |
|---|---|
| Model Adı | 1027 |
| Modül Tipi | Saatli Sıralı Kontrol Modülü |
| Seri | 2500 Serisi |
| Biçim | EURORACK |
| Genişlik | 16 beygir |
| Derinlik | Not specified (typical Eurorack depth) |
| Güç Tüketimi | Not specified (standard Eurorack +12V, -12V) |
| Girişler | Clock In, External Pulse Width CV |
| Çıktılar | 3 x CV (A, B, C), 8 x Gate (Position Gates) |
| Boyutlar (Y x G x D) | 43 x 162 x 129 mm (yaklaşık 1.69 x 6.38 x 5.08 inç) |
| Ürün Ağırlığı | 0.77 Pound (yaklaşık 0.35 kg) |
| Bağlantı Teknolojisi | 3.5mm TS jack |
| Güç Kaynağı | DC power supply (via Eurorack bus) |
Garanti
Behringer products are covered by a limited warranty. For detailed information regarding warranty terms, conditions, and registration, please visit the official Behringer website or the Music Tribe Community portal. Warranty services are typically handled through authorized service centers.
Garanti Açıklaması: Community. Musictribe. Com.
Destek
For further assistance, technical support, or to download the latest firmware and documentation, please visit the official Behringer webalan:
- Behringer Resmi Webalan
- Music Tribe Community (for warranty and support information)
You can also contact your local Behringer dealer or distributor for product-specific inquiries.