POTTER VSR-3 Kanatlı Tip Su Akış Alarm Anahtarı

giriiş

The POTTER VSR-3 is a vane type water flow alarm switch designed for use on 3-inch steel pipes. It is intended to detect a sustained flow of water in fire sprinkler systems, activating an alarm when flow conditions are met. This device is crucial for indicating the operation of sprinkler systems in the event of a fire.

Güvenlik Bilgileri

Always adhere to local codes and regulations during installation and maintenance. Disconnect all power sources before servicing the device. Installation should only be performed by qualified personnel. Failure to follow these instructions could result in property damage, serious injury, or death.

• Ensure the system is depressurized before installation or removal.
• Uygun kişisel koruyucu ekipman (KKE) giyin.
• Verify correct wiring to prevent electrical hazards.

Kurulum ve Yükleme

The VSR-3 switch is designed for horizontal or vertical pipe installation. Ensure the arrow on the switch housing aligns with the direction of water flow.

1. Kurulum Öncesi Kontroller

• Confirm the pipe size is 3 inches.
• Inspect the switch for any damage.
• Gerekli tüm araç ve gereçlerin mevcut olduğundan emin olun.

2. Montaj Talimatları

The VSR-3 mounts to the pipe using a saddle-type connection. A hole must be drilled into the pipe for the vane to be inserted.

1. Depressurize and drain the pipe section where the switch will be installed.
2. Drill a 1-1/4 inch (32 mm) hole in the pipe. Remove any burrs.
3. Apply a suitable sealant to the saddle gasket.
4. Position the saddle and switch assembly over the drilled hole, ensuring the flow arrow on the switch points in the direction of water flow.
5. Secure the assembly with the provided U-bolt and nuts, tightening evenly to create a watertight seal. Do not overtighten.

3. Kablolama Talimatları

The VSR-3 contains two sets of SPDT (Single-Pole, Double-Throw) contacts. Refer to the wiring diagram inside the switch cover for specific connections.

• Connect the alarm circuit wiring to the appropriate terminals.
• Tüm bağlantıların güvenli ve yalıtılmış olduğundan emin olun.
• Verify that the electrical supply matches the switch's rating.

Kullanım Talimatları

The VSR-3 is designed to activate an alarm when a sustained flow of water, equivalent to or greater than the flow from a single sprinkler head, occurs in the pipe. The time delay feature prevents false alarms due to pressure surges.

1. Alarm Activation

When water flows through the pipe and deflects the vane, the switch contacts change state after a preset time delay. This activates connected alarm devices (e.g., bells, panels).

2. Testing Procedures

Regular testing is essential to ensure proper operation. Follow NFPA 25 guidelines for inspection, testing, and maintenance of water-based fire protection systems.

• Haftalık/Aylık: Visually inspect the switch for physical damage or corrosion.
• Quarterly/Annually: Conduct a full flow test by opening the inspector's test connection or a drain valve downstream of the switch. Verify that the alarm activates within the specified time delay (typically 5-90 seconds).
• Restore the system to normal operating conditions after testing.

Bakım

The VSR-3 requires minimal maintenance. Regular inspections and functional testing are the primary maintenance activities.

• Keep the exterior of the switch clean and free from debris.
• Check for any signs of water leakage around the saddle connection.
• Ensure the conduit connections are tight and free from moisture.
• Do not attempt to lubricate or modify internal components.

Sorun giderme

Özellikler

Garanti ve Destek

For warranty information and technical support, please contact POTTER directly or refer to the official documentation provided with your purchase. Keep your purchase receipt for warranty claims.

İletişim Bilgileri: Üreticinin resmi açıklamasına bakın webEn güncel iletişim bilgileri için lütfen siteye veya ambalaja bakın.