1. Giriş
The Selec CH-403-2 is a precision temperature chiller controller designed for industrial and commercial applications requiring accurate temperature regulation. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your device. Please read this manual thoroughly before installation and operation.
2. Güvenlik Bilgileri
Yaralanmaları ve cihaz hasarını önlemek için her zaman aşağıdaki güvenlik önlemlerine uyun:
- Herhangi bir kablolama veya bakım işlemi yapmadan önce güç kaynağının bağlantısının kesildiğinden emin olun.
- Kurulum ve servis işlemleri yalnızca kalifiye personel tarafından yapılmalıdır.
- Güç kaynağı hacminin doğru olduğundan emin oluntage, kontrol cihazının özelliklerine uygundur.
- Do not expose the controller to excessive moisture, dust, or corrosive gases.
- Elektrik çarpmasını önlemek için topraklamanın uygun olduğundan emin olun.
3. Kurulum
3.1 Paketin açılması
Carefully remove the controller from its packaging. Inspect the device for any signs of damage during transit. Report any damage to your supplier immediately.
3.2 Montaj
The CH-403-2 is designed for panel mounting. Cut an opening of 45mm x 45mm (1.77" x 1.77") in the panel. Insert the controller into the opening and secure it using the provided mounting clamps. Ensure a snug fit to prevent dust and moisture ingress.
3.3 Kablo Bağlantıları
Refer to the wiring diagram located on the side of the controller or in the detailed technical specifications. Ensure all connections are secure and correct before applying power.
- Güç Kaynağı: Uygun AC voltaj bağlantısını yapın.tage (e.g., 230V AC) to the designated power terminals.
- Sensör Girişi: Connect the temperature sensor (e.g., NTC, PT100) to the sensor input terminals. Observe polarity if applicable.
- Kontrol Çıkışı: Connect the chiller or heating element to the relay output terminals. Ensure the load current does not exceed the relay's maximum rating.
- Alarm Output (Optional): If applicable, connect external alarm devices to the alarm output terminals.
3.4 İlk Güçlendirme
After all connections are verified, apply power to the controller. The display should illuminate, showing the current temperature and default settings.
4. Çalıştırma
4.1 Ekran Üstüview
The front panel features a digital display showing the process value (PV) and set point (SV), along with indicator LEDs for output status (e.g., ON/OFF, Alarm).
4.2 Düğme Fonksiyonları
- Ayarlama düğmesi: Parametre ayarlama moduna girmek ve seçimleri onaylamak için kullanılır.
- YUKARI/AŞAĞI Düğmeleri: Parametreler arasında gezinmek ve değerleri ayarlamak için kullanılır.
- MOD Düğmesi: Used to switch between display modes or access advanced settings.
4.3 Setting Temperature Setpoint (SV)
- Basın AYARLAMAK button once. The SV value will flash.
- Kullanın UP or AŞAĞI buttons to adjust the setpoint to the desired temperature.
- Basın AYARLAMAK button again to confirm the new setpoint. The display will return to showing the PV.
4.4 Parametre Yapılandırması
To access advanced parameters such as hysteresis, calibration offset, or delay times, press and hold the AYARLAMAK İlk parametre kodu görünene kadar düğmeye birkaç saniye basılı tutun. Kullanın YUKARI/AŞAĞI buttons to navigate through parameters and the AYARLAMAK button to select and modify values. Refer to the detailed parameter list in the full technical manual for specific codes and ranges.
5. Bakım
5.1 Temizlik
Clean the front panel of the controller periodically with a soft, damp Bez kullanın. Aşındırıcı temizleyiciler veya çözücüler kullanmayın, çünkü bunlar ekranı veya cihazı hasar verebilir.asing. Cihaza hiçbir sıvının girmemesini sağlayın.
5.2 Düzenli Kontroller
- Inspect wiring connections for looseness or corrosion.
- Verify the temperature sensor is clean and properly installed.
- Check for any unusual noises or smells from the controller or connected equipment.
5.3 Kalibrasyon
If temperature readings appear inaccurate, the sensor or controller may require calibration. Refer to the advanced parameter settings for sensor offset adjustment. For precise calibration, consult a qualified technician.
6. Sorun Giderme
Bu bölümde karşılaşabileceğiniz yaygın sorunlar ele alınmaktadır. Burada listelenmeyen sorunlar için teknik destekle iletişime geçin.
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| No display / Power off | Güç kaynağı yok; Yanlış kablolama; Sigorta atmış | Güç bağlantılarını kontrol edin; Voltajı doğrulayın.tage; Replace fuse if necessary. |
| Yanlış sıcaklık okuması | Sensor faulty; Sensor wiring incorrect; Calibration offset needed | Check sensor connections; Replace sensor; Adjust calibration offset in parameters. |
| Çıkış değiştirilmiyor | Setpoint not reached; Hysteresis setting too wide; Output relay faulty | Verify setpoint and current temperature; Adjust hysteresis; Test output relay (by qualified personnel). |
| Hata Kodu 'E1' | Sensör açık devre | Check sensor wiring for breaks; Replace sensor. |
| Hata Kodu 'E2' | Sensör kısa devre | Check sensor wiring for shorts; Replace sensor. |
7. Özellikler
| Parametre | Değer |
|---|---|
| Örnek | ÇB-403-2 |
| Giriş Türü | NTC / PT100 (selectable) |
| Sıcaklık Aralığı | -50°C to 150°C (sensor dependent) |
| Kontrol Çıkışı | 1 x Relay (NO/NC), 5A @ 250V AC resistive |
| Yardımcı Çıkış | 1 x Relay (NO), 3A @ 250V AC resistive (Alarm) |
| Tedarik Hacmitage | 230V AC ±10%, 50/60 Hz |
| Kesinlik | ±1% of full scale ±1 digit |
| Görüntülemek | 3 basamaklı LED |
| Montaj | Panel Mount (45x45mm cutout) |
| Çalışma Sıcaklığı | 0°C ila 50°C |
| Boyutlar (GxYxD) | 48mm x 48mm x 85mm |
8. Garanti ve Destek
Selec products are covered by a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Selec website. For technical support, service, or spare parts, please contact your authorized Selec distributor or customer service department, providing your product model number (CH-403-2) and serial number.