1. Giriş ve Üzeriview
The EPEVER Tracer4210AN is a 40A MPPT (Maximum Power Point Tracking) solar charge controller designed for 12V and 24V DC systems. It efficiently regulates power from solar panels to charge various battery types, including lead-acid (Sealed, AGM, GEL, Flooded) and lithium (LiFePO4, Li(NiCoMn)O2) batteries. This controller features an advanced MPPT control algorithm for high tracking and conversion efficiency, ensuring optimal energy harvest from your solar array. It includes multiple built-in protections for safe and stable operation, and an LCD screen for easy monitoring and parameter customization.
Şekil 1.1: Ön View of the EPEVER Tracer4210AN Controller.
Şekil 1.2: Geri View of the EPEVER Tracer4210AN Controller.
2. Güvenlik Bilgileri
Before installing or operating the EPEVER Tracer4210AN solar charge controller, please read all instructions carefully. Improper installation or operation can lead to equipment damage, personal injury, or property damage. Always ensure proper ventilation around the controller. Do not expose the controller to water or excessive humidity. Disconnect all power sources before performing any maintenance or adjustments.
Important Connection Order: Always connect the battery first, then the load, and finally the solar panel. When disconnecting, reverse this order: disconnect the solar panel, then the load, and finally the battery.
3. Ürün Özellikleri
- Advanced MPPT control algorithm for tracking efficiency greater than 98% and peak conversion efficiency of 99.5%.
- Automatic identification of 12V/24V DC system voltage.
- Supports various battery types: Lead-acid (Sealed, AGM, GEL, Flooded) and Lithium (LiFePO4, Li(NiCoMn)O2, User-defined).
- Built-in multiple protections: PV over-voltage, pil aşırı voltajtage, over-temperature, over-charging, short-circuit, reverse polarity, and temperature compensation.
- Informative LCD screen and two buttons for customizable parameters and display of working status.
- 4-stage battery charging (Bulk, Boost, Float, and Equalization).
- Common negative grounded design.
Figure 3.1: MPPT Tracking and Charge Conversion Efficiency.
Figure 3.2: Multiple Protection Features of the Controller.
4. Paket İçeriği
The package for your EPEVER Tracer4210AN solar charge controller typically includes:
- EPEVER Tracer4210AN MPPT Güneş Şarj Kontrol Cihazı
- Kullanıcı Kılavuzu
- Kalite Belgesi
- Small green connector (for temperature sensor)
Video 4.1: Kutudan çıkarma ve sonrasıview of the EPEVER Tracer-AN Series MPPT Solar Charge Controller (demonstrated with a Tracer3210AN model), showing package contents and physical features.
5. Kurulum ve Kurulum
Follow these steps for proper installation. Always ensure correct polarity and secure connections to prevent damage.
- Pili bağlayın: Loosen the screws on the battery terminals of the controller. Connect the positive (+) and negative (-) battery cables to the corresponding terminals. Ensure the connection is secure. The controller will automatically detect the system voltage (12V/24V).
- Yükü bağlayın: Loosen the screws on the load terminals. Connect the positive (+) and negative (-) load cables to the corresponding terminals.
- Güneş Panelini Bağlayın: Loosen the screws on the solar panel (PV) terminals. Connect the positive (+) and negative (-) solar panel cables to the corresponding terminals.
- Sıcaklık Sensörünü Bağlayın (İsteğe Bağlı): Insert the remote temperature sensor into the designated port on the controller. This allows for accurate battery temperature compensation during charging.
Önemli: Always connect the battery first, then the load, and finally the solar panel. When disconnecting, reverse this order: disconnect the solar panel, then the load, and finally the battery.
Figure 5.1: Basic Connection Diagram for the Solar Charge Controller.
Figure 5.2: Supported Battery Types for the Controller.
6. Kullanım Talimatları
The controller features an LCD display and two buttons ("SELECT" and "ENTER") for monitoring system status and configuring parameters.
6.1 LCD Ekran ve Düğme Fonksiyonları
The LCD displays various system parameters such as battery voltage, charging current, load current, and temperature. Use the "SELECT" button to browse through different display interfaces and the "ENTER" button to confirm selections or enter settings mode.
Figure 6.1: LCD Display showing system parameters.
6.2 Pil Türünün Ayarlanması
Pil türünü ayarlamak için:
- Press the "ENTER" button and hold for 5 seconds under the battery voltage arayüzü.
- Press the "SELECT" button when the battery type interface is flashing to cycle through available battery types (SEL, GEL, FLD, LiFePO4, Li(NiCoMn)O2, USE).
- Seçilen pil tipini onaylamak için "ENTER" düğmesine basın.
Figure 6.2: Steps for Setting Battery Type via LCD.
6.3 Yük Çalışma Modunun Ayarlanması
To set the load working mode:
- Press the "ENTER" button and hold for 5 seconds under the load mode interface.
- Press the "SELECT" button when the load mode interface is flashing to choose the desired mode.
- Press the "ENTER" button to confirm the load mode.
Dikkat: Setting Light ON/OFF, Test mode, and Manual mode via Timer1. Timer2 will be disabled and display "2n".
