giriiş
This manual provides instructions for the installation, operation, and maintenance of your new 2200mAh LIP1522 replacement battery for compatible Sony PlayStation 4 Dualshock 4 wireless controllers. Please read this manual thoroughly before proceeding with installation to ensure proper use and safety.
Image: The 2200mAh LIP1522 replacement battery, designed for compatible PS4 controllers. The battery label indicates 'Lithium Polymer battery + 2200mAh 3.7V 8.14Wh'.
Önemli Güvenlik Bilgileri
Please observe the following safety precautions to prevent damage to the battery, controller, or personal injury:
- Pili sökmeyin, delmeyin veya üzerinde değişiklik yapmayın.
- Do not expose the battery to extreme temperatures (hot or cold), direct sunlight, or fire.
- Pili sudan veya diğer sıvılardan uzak tutun.
- If the battery appears damaged, swollen, or leaks, discontinue use immediately and dispose of it properly.
- Use only approved charging methods for your PS4 controller.
- Çocukların erişemeyeceği yerde saklayınız.
Paket İçeriği
Paketin içinde tüm öğelerin mevcut olduğundan emin olun:
- 1 x 2200mAh LIP1522 Replacement Battery
Uyumluluk
This replacement battery is designed for specific models of the Sony PlayStation 4 Dualshock 4 wireless controller. Please check your controller's model number, typically located on a label on the back of the controller, to ensure compatibility.
Compatible Controller Models:
- CUH-ZCT1E
- CUH-ZCT1H
- CUH-ZCT1H/B
- CUH-ZCT1H/R
- CUH-ZCT1U
ÖNEMLİ NOT: Bu pil Uyumlu değil with 2016 (or newer) controller models such as CUH-ZCT2 or CUH-ZCT2U. These newer models use a different battery connector. Please verify your controller's model number and battery plug type before installation.
Image: A visual comparison showing a 'Small plug LIP1522' and a 'Big plug LIP1522', with the replacement battery featuring the 'Big plug' type, indicating compatibility with PS4 CUH-ZCT1U controllers.
Kurulum Talimatları
Follow these steps carefully to replace the battery in your compatible PS4 Dualshock 4 controller. You will need a small Phillips head screwdriver (not included).
- Kontrol cihazını hazırlayın: Ensure your PS4 controller is powered off.
- Vidaları çıkarın: Locate the four small Phillips head screws on the back of the controller. Carefully remove them.
- C'yi açınasing: Gently pry open the controller casing. Start from the seam near the shoulder buttons and work your way around. Be cautious of the ribbon cable connecting the two halves.
- Eski Aküyü Çıkarın: Locate the existing battery. Carefully disconnect its plug from the controller's circuit board.
- Eski Pili Çıkarın: Eski pili bölmesinden çıkarın.
- Yeni Aküyü Bağlayın: Take your new 2200mAh LIP1522 battery. Align the connector plug with the port on the controller's circuit board and gently push it in until it is securely seated.
- Yeni Pilin Yerini Belirleyin: Place the new battery into the battery compartment. Ensure it fits snugly and the wires are not pinched.
Image: The 2200mAh LIP1522 replacement battery correctly installed within the open casing of a PS4 controller, showing the battery seated in its compartment and connected to the circuit board.
- Kontrol ünitesini yeniden monte edin: Carefully bring the two halves of the controller casing back together. Ensure all clips align and the ribbon cable is not damaged.
- Replace Screws: Reinsert and tighten the four Phillips head screws on the back of the controller. Do not overtighten.
- Test Controller: Power on your PS4 controller to confirm the new battery is functioning correctly.
Şarj etme
After installation, fully charge the new battery before its first use. Connect your PS4 controller to your PlayStation 4 console or a compatible USB charging source using a USB cable. The controller's light bar will indicate charging status.
Bakım
To maximize the lifespan and performance of your battery:
- Pilin düzenli olarak tamamen boşaltılmasından kaçının.
- Kontrol cihazını kullanılmadığı zaman serin ve kuru bir yerde saklayın.
- Uzun süre saklanacaksa, pili yaklaşık %50 kapasiteye kadar şarj edin.
Sorun giderme
| Sorun | Olası Çözüm |
|---|---|
| Controller does not power on after battery replacement. | Ensure the battery connector is securely plugged into the circuit board. Verify the controller model is compatible with this battery. Try connecting the controller to the PS4 console via USB cable to initiate charging. |
| Pil şarj olmuyor. | Check the USB charging cable and port for damage. Ensure the battery is correctly installed. If the issue persists, the battery or controller may be faulty. |
| Pil ömrü beklenenden daha kısa. | Ensure the battery was fully charged before use. Some games or controller features (e.g., vibration, light bar brightness) consume more power. |
| Battery does not fit in the controller. | Double-check your controller's model number. This battery is specifically for CUH-ZCT1U and similar first-generation PS4 controllers. It is not compatible with CUH-ZCT2U models. |
Özellikler
| Özellik | Detay |
|---|---|
| Pil Türü | Lityum Polimer |
| Kapasite | 2200mAh |
| Nominal Hacimtage | 3.7V |
| Enerji | 8.14Wh |
| Ağırlık | Yaklaşık 1.27 ons (36 gram) |
| Model Numarası | Cuh-zct1e battery (LIP1522 type) |
| Marka | Bilinmeyen |
Garanti ve Destek
For warranty information or technical support, please refer to the seller or manufacturer's contact details provided at the point of purchase. Keep your proof of purchase for any warranty claims.