giriiş
This manual provides detailed instructions for the installation, operation, and maintenance of your Claber 90763 Timer Kit 20 Practico. This automatic drip irrigation system is designed for watering up to 20 potted plants on terraces or patios, ensuring efficient and consistent hydration.
Güvenlik Bilgileri
- Don Yok: Do not expose the timer or system components to freezing temperatures.
- Çocuklar İçin Uygun Değildir: Ürünü çocukların erişemeyeceği yerde saklayınız.
- Yalnızca Dış Mekan Kullanımı: Bu ürün dış mekan kurulumu için tasarlanmıştır.
- Daldırmayın: The timer unit must not be placed underwater.
- Valve Box Installation: Do not install the timer inside a valve box.
- Su Basıncı: Ensure water pressure is between 0.5 bar (7.3 psi) and 10 bar (145 psi).
Paket İçeriği
Kitinizde tüm bileşenlerin eksiksiz olduğundan emin olun:
Image: All components of the Claber 90763 Timer Kit 20 Practico, including the timer, main hose, drippers, stakes, and connectors.
- 1x Aquauno Pratico Timer
- 1x Pressure Stabilizer
- 1x 20m (1/4" - 4-6mm) Main Hose
- 20x Adjustable Drippers
- 20x Stakes for Drippers
- Various Connectors and Fittings (e.g., 3-way connectors, end caps)
Kurulum Talimatları
1. Pil Kurulumu
- Open the battery compartment on the back of the Aquauno Pratico timer.
- Insert one new 9V alkaline battery, ensuring correct polarity.
- Pil bölmesini sıkıca kapatın.
Image: A section from the instruction manual illustrating the steps for inserting a 9V battery into the timer.
Not: The timer requires a 9V alkaline battery (not included). If the battery is low, the timer's LED will flash. Replace the battery promptly to avoid interruption of watering cycles.
2. Timer and Pressure Stabilizer Installation
- Attach the pressure stabilizer to the outlet of the Aquauno Pratico timer.
- Screw the timer onto a standard 3/4" outdoor tap. Ensure a tight, leak-free connection.
- The timer should be installed vertically, with the display facing outwards for easy access.
Image: The Claber Aquauno Pratico timer connected to an outdoor water tap, with the pressure stabilizer attached below it.
3. Drip System Assembly
- Connect the main hose (1/4" or 4-6mm) to the outlet of the pressure stabilizer.
- Lay out the main hose to reach all potted plants you intend to water.
- At each plant location, cut the main hose and insert a 3-way connector or a direct dripper connection.
- Attach the adjustable drippers to the hose or connectors.
- Use the provided stakes to secure the drippers near the base of each plant.
- Cap the end of the main hose with an end cap to maintain pressure.
Image: An illustration of a balcony with potted plants being watered by the Claber drip irrigation system, showing hose routing and dripper placement.
Kullanım Talimatları
1. Programming the Aquauno Pratico Timer
The Aquauno Pratico timer allows for daily watering with a maximum duration of 60 minutes. Refer to the timer's interface for specific programming steps:
Resim: Ayrıntılı view of the Claber Aquauno Pratico timer, showing the control buttons and display area.
- Start Button (Green): Press to initiate a watering cycle or confirm a setting.
- Durdurma Butonu (Kırmızı): Press to stop an ongoing watering cycle or cancel a setting.
- Programlama Kadranı: Rotate the dial to select the desired watering duration (e.g., 5, 10, 15, 20, 30, 45, 60 minutes). The timer will automatically water daily for the selected duration.
- Reset/Cancel Button: Use to reset the timer or cancel current programming.
For detailed programming steps, refer to the specific instructions provided on the timer unit or the full manual available online.
2. Adjusting Drippers
Each dripper is adjustable to control the water flow to individual plants. Rotate the cap on each dripper to increase or decrease the water output. Adjust the flow based on the plant's water requirements and soil type.
Bakım
- Temizlik: Wipe the timer and components with a damp Gerektiğinde bezle silin. Aşındırıcı temizleyiciler kullanmayın.
- Filtre Temizleme: The timer includes a filter at the inlet. Periodically remove and clean this filter to prevent blockages and ensure proper water flow.
- Kışlama: Before the first frost, disconnect the timer and drain all water from the system. Store the timer and components in a dry, frost-free location. Remove the battery before storage.
- Pil Değişimi: Replace the 9V alkaline battery annually or when the low battery indicator flashes.
Sorun giderme
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Timer does not start watering. | Dead or low battery. Incorrect programming. Water tap is off. | Replace battery. Re-program the timer. Ensure water tap is fully open. |
| No water flow from drippers. | Clogged filter. Kinked hose. Drippers are closed. Low water pressure. | Clean the inlet filter. Check hose for kinks. Open drippers. Ensure adequate water pressure. |
| Bağlantılardan su sızıyor. | Loose connections. Damaged O-rings/washers. | Tüm bağlantıları sıkın. Hasarlı O-ringleri veya rondelaları kontrol edin ve gerekirse değiştirin. |
| Inconsistent watering. | Uneven water pressure. Partially clogged drippers. | Ensure pressure stabilizer is correctly installed. Clean drippers. |
Özellikler
- Marka: Claber
- Modeli: 90763 (Timer Kit 20 Practico)
- Malzeme: Plastik
- Product Dimensions (Timer): 2.36"D x 3.15"G x 4.33"Y
- Item Weight (Timer): Yaklaşık 0.037 ons (1.05 gram)
- Sulama Sıklığı: Günlük
- Sulama Süresi: Up to 60 minutes (adjustable)
- Güç Kaynağı: 1x 9V Alkaline Battery (not included)
- Su Basıncı Aralığı: 0.5 - 10 bar (7.3 - 145 psi)
- Bakım Talimatları: D ile silinamp Kumaş
Garanti ve Destek
For warranty information, technical support, or additional resources, please visit the official Claber websitesine gidin veya müşteri hizmetleriyle iletişime geçin.
Çevrimiçi Kaynaklar: Claber Instruction Manuals
Üretici: Claber