Ürün Bittiview
This manual provides instructions for the Tenergy 9.6V (8S) NiMH/NiCd RC Battery Charger, designed for use with RC hobbies. It features a 400mA AC plug and a standard Tamiya connector. This charger is specifically for 9.6V NiMH/NiCd battery packs and is not compatible with LiPo batteries or other voltage battery types.
Image: The Tenergy 9.6V NiMH/NiCd RC Battery Charger with its standard Tamiya connector.
Güvenlik Talimatları
- Only use this charger with 9.6V (8S) NiMH or NiCd battery packs. Do not attempt to charge LiPo batteries or any other battery chemistry.
- Bu şarj cihazı uyumlu değil with Spike the Dinosaur or similar toys requiring specific charging protocols.
- Ensure the battery connector is a standard Tamiya type. Incompatible connectors may cause damage.
- Şarj eden pilleri gözetimsiz bırakmayın.
- Şarj cihazını ve pili yanıcı maddelerden uzak tutun.
- Şarj cihazını neme veya aşırı sıcaklıklara maruz bırakmayın.
- If the charger or battery shows signs of damage, discontinue use immediately.
Kurmak
Before first use, inspect the charger and battery for any visible damage. Ensure the battery pack is a 9.6V NiMH or NiCd type with a standard Tamiya connector.
- Locate a standard AC power outlet (100-240V).
- Plug the charger's AC plug into the power outlet. The LED indicator on the charger will illuminate.
- Connect the standard Tamiya connector from your 9.6V NiMH/NiCd battery pack to the charger's output connector. Ensure a secure connection.
Image: Diagram showing the dimensions of a standard Tamiya connector, emphasizing compatibility. This charger is only compatible with white standard Tamiya connectors, not mini Tamiya connectors.
Image: The Tenergy charger plugged into a power strip, ready to connect to a battery pack.
Kullanım Talimatları
Pilinizi Şarj Etme
Once the charger is plugged into an AC outlet and connected to a compatible 9.6V NiMH/NiCd battery pack, the charging process will begin automatically.
- LED Göstergesi: The charger features a simple LED indicator to show charging status.
- Düz Kırmızı: Pil şu anda şarj ediliyor, bunu gösterir.
- Düz Yeşil: Pilin tamamen şarj olduğunu gösterir.
Image: Close-up of the charger showing a red LED for charging and a green LED for fully charged status.
For a 2000mAh battery pack, the estimated charge time from empty is approximately 5-6 hours at a 400mA charging speed. Charging times may vary based on battery capacity and discharge level.
Image: The Tenergy charger connected to a 9.6V 2000mAh NiMH battery pack, illustrating the charging process.
Cilttage Uyumluluk
This charger is designed for 9.6V (8S) NiMH and NiCd battery packs. Always verify your battery's voltage and chemistry before connecting to prevent damage.
Image: Two different styles of 9.6V (8S) NiMH battery packs, demonstrating the charger's voltage uyumluluk.
Bakım
- Şarj cihazını temiz tutun ve tozdan ve kirden arındırın. Temizlik için kuru bir bez kullanın.
- Şarj cihazını kullanmadığınız zamanlarda serin ve kuru bir yerde saklayın.
- Avoid wrapping the cable too tightly around the charger to prevent wire damage.
Sorun giderme
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Şarj cihazının LED'i yanmıyor. | No power from AC outlet; charger or cable damaged. | Check AC outlet with another device. Inspect charger and cable for damage. If damaged, discontinue use. |
| Charger LED remains red after extended charging. | Battery not fully charged; faulty battery; charger malfunction. | Allow more time for charging. Test battery with another compatible charger if available. Contact support if issue persists. |
| Charger LED is green but battery is not fully charged. | Charger malfunction; battery issue. | Ensure battery is properly connected. If the issue persists, the charger may be faulty. |
| Şarj cihazı aşırı derecede ısınıyor. | Overload; internal fault. | Immediately disconnect the charger and battery. Do not use if it overheats. Contact support. |
Özellikler
- Model Numarası: 01009
- Giriş Voltage: 100-240V AC
- Çıkış Hacmitage: 12 Volt
- Şarj Akımı: 400mA
- Uyumlu Pil Tipleri: NiMH, NiCd
- Uyumlu Pil Hacmitage: 9.6V (8S)
- Bağlantı Tipi: Standard Tamiya
- Ürün Ağırlığı: 3.21 ons (0.2 Pound)
- Paket Boyutları: 3.82 x 1.5 x 1.1 inç
- Sertifikasyon: CE Uyumlu
Garanti ve Destek
This Tenergy charger includes a 12 ay garanti from the date of purchase. For warranty claims, technical support, or any questions regarding the product, please contact Tenergy Corporation directly. Refer to the product packaging or the official Tenergy webEn güncel iletişim bilgileri için sitemizi ziyaret edin.
Ürün Videoları
Tenergy 9.6V Charger Overview
Video: An official product video from Tenergy Corporation demonstrating the features and use of the 9.6V charger for RC hobbies. This video highlights voltage compatibility and ease of use.