giriiş
This manual provides essential instructions for the safe operation, maintenance, and storage of your Performance Tool W1611 2.25 Ton (4,500 lbs) Capacity Trolley Jack. Before using the jack, it is crucial to read and understand all instructions and safety warnings to prevent injury or property damage. Keep this manual for future reference.
Image: The Performance Tool W1611 2.25 Ton Trolley Jack, a yellow hydraulic jack with a long handle.
Önemli Güvenlik Bilgileri
WARNING: Failure to heed these warnings may result in personal injury or property damage.
- Tüm talimatları okuyunuz: Understand the operation and limitations of the jack, as well as the hazards involved.
- Sert ve düz bir yüzeyde kullanın: Always use the jack on a hard, level surface capable of supporting the load. Avoid soft ground or uneven surfaces.
- Do Not Exceed Rated Capacity: The W1611 jack has a maximum capacity of 2.25 tons (4,500 lbs). Do not attempt to lift loads heavier than this rating.
- Kriko Ayaklarını Kullanın: This jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Never work under a vehicle supported only by a jack.
- Yükü ortalayın: Ensure the load is centered on the jack saddle. Off-center loads can cause instability.
- Açık Tutun: Ellerinizi, ayaklarınızı ve diğer vücut kısımlarınızı hareketli parçalardan ve yükün altındaki alandan uzak tutun.
- Her Kullanımdan Önce Kontrol Edin: Check the jack for any damage, leaks, or loose parts before each use. Do not use if damaged.
- Yavaşça indirin: Always lower the load slowly and in a controlled manner.
- Öneri 65 Uyarısı: Bu ürün, Kaliforniya Eyaleti tarafından kansere, doğum kusurlarına veya üremeyle ilgili diğer zararlara neden olduğu bilinen kimyasallar içerebilir. Elleçlemeden sonra ellerinizi yıkayın.
Paket İçeriği
Paketi açtığınızda tüm bileşenlerin mevcut olduğundan emin olun:
- 1 Performance Tool W1611 2.25 Ton Trolley Jack
- 1 Operating Handle
- 1 Blow-molded plastic storage case
Özellikler
| Özellik | Şartname |
|---|---|
| Örnek | W1611 |
| Yük Kapasitesi | 2.25 Ton (4,500 lbs) |
| Minimum Kaldırma Yüksekliği | 5-1/4 inç |
| Maksimum Kaldırma Yüksekliği | 15 inç |
| Ürün Boyutları (U x G x Y) | 23.2 x 10.3 x 6.8 inç |
| Ürün Ağırlığı | Approximately 27 lbs (including case) |
| Sele | Steel lifting saddle with 360-degree swivel |
| Tekerlekler | Heavy-duty steel front wheels, ball-bearing swivel rear wheels |
Resim: Yakın çekim view highlighting the steel lifting saddle and the heavy-duty wheels of the trolley jack.
Kurulum ve İlk Hazırlık
1. Paketten çıkarma
Carefully remove the trolley jack and its components from the packaging. Inspect for any shipping damage. If any damage is found, do not use the jack and contact customer support.
2. Kulp Montajı
Insert the operating handle into the handle socket on the jack. Ensure it is securely seated. Some models may require tightening a set screw.
3. Bleeding the Hydraulic System
Before first use, or if the jack has been stored for an extended period, it is recommended to bleed any air from the hydraulic system to ensure proper operation. This procedure helps distribute fluid evenly through internal components.
- Locate the release valve (typically a screw or knob near the handle socket).
- Turn the release valve counter-clockwise to open it fully.
- Pump the handle vigorously six (6) to ten (10) times. This action will cycle the hydraulic fluid and expel any trapped air.
- Turn the release valve clockwise to close it firmly. The jack is now ready for use.
Kullanım Talimatları
1. Bir Aracı Kaldırmak
- Aracı Hazırlayın: Park the vehicle on a hard, level surface. Engage the parking brake and place the transmission in 'Park' (automatic) or 'Reverse' (manual). Block the wheels that will remain on the ground to prevent movement.
- Krikoyu yerleştirin: Locate the manufacturer-recommended lifting points on your vehicle's frame or chassis. Position the jack so the saddle is directly under the lifting point. Ensure the jack is stable and the load is centered on the saddle.
- Aracı Kaldırın: Close the release valve by turning it clockwise until it is firm. Pump the operating handle up and down to raise the vehicle to the desired height.
- Kriko ayaklarıyla sabitleyin: Once the vehicle is lifted, immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by gradually turning the release valve counter-clockwise. Ensure the vehicle is stable on the jack stands before performing any work.
2. Aracın İndirilmesi
- Alanı Temizle: Ensure all tools, personnel, and obstructions are clear from under and around the vehicle.
- Raise Slightly: If the vehicle is on jack stands, pump the jack handle a few times to lift the vehicle slightly off the jack stands.
- Kriko ayaklarını çıkarın: Krikoları aracın altından dikkatlice çıkarın.
- Aracı alçaltın: Slowly turn the release valve counter-clockwise to gradually lower the vehicle to the ground. Once fully lowered, remove the jack.
Image: The Performance Tool W1611 trolley jack positioned for lifting, demonstrating its extended handle and low profile.
Bakım
Regular maintenance ensures the longevity and safe operation of your trolley jack.
- Temizlik: Keep the jack clean and free of dirt, grease, and debris. Wipe down the exterior with a clean cloth after each use.
- Yağlama: Periodically lubricate the pivot points, wheels, and especially the wheel castor bearings with light machine oil to ensure smooth operation and prevent rust.
- Hidrolik Sıvı: Check the hydraulic fluid level periodically. If the fluid level is low, consult a qualified service technician for proper refilling with hydraulic jack oil. Do not use brake fluid or other non-specified fluids.
- Denetleme: Regularly inspect the jack for any signs of wear, damage, or leaks. Pay close attention to welds, the hydraulic cylinder, and the handle. If any issues are found, discontinue use and have it repaired by a qualified professional.
Sorun giderme
Yaygın sorunlar ve olası çözümleri için aşağıdaki tabloya bakın.
| Sorun | Olası Neden | Çözüm |
|---|---|---|
| Jack will not lift or lifts slowly | Hidrolik sistemde hava Düşük hidrolik sıvı seviyesi Serbest bırakma valfi tamamen kapalı değil | Bleed the hydraulic system (refer to Setup section) Consult a qualified technician to check/refill fluid Ensure release valve is firmly closed clockwise |
| Jack lowers under load | Serbest bırakma valfi tamamen kapalı değil Internal hydraulic leak Aşırı yük | Ensure release valve is firmly closed Discontinue use and consult a qualified technician Ensure load does not exceed 2.25 tons (4,500 lbs) |
| Jack is difficult to pump | Hidrolik sistemde hava Hareketli parçalarda yağlama eksikliği Hasarlı pompa mekanizması | Hidrolik sistemin havasını alın Lubricate pivot points and wheels Kalifiye bir teknisyene danışın |
Depolamak
Proper storage helps maintain the jack's condition and readiness for use.
- Depolamadan Önce Temizlik: Ensure the jack is clean and dry before storing.
- Lower Ram Fully: Always lower the jack's ram completely before storage to relieve pressure on the hydraulic system.
- Saklama Kutusunu Kullanın: Store the jack in its provided blow-molded plastic case to protect it from dust, moisture, and damage. This also prevents it from rolling around if stored in a vehicle.
- Kuru bir yerde saklayın: Store the jack in a dry, protected area, away from corrosive materials and extreme temperatures.
Image: The Performance Tool W1611 trolley jack alongside its durable black plastic storage case, emphasizing portability and protection.
Garanti ve Destek
For warranty information or technical support regarding your Performance Tool W1611 2.25 Ton Trolley Jack, please refer to the documentation included with your purchase or visit the official Performance Tool webMüşteri hizmetleriyle ilgili iletişim bilgileri genellikle üreticinin web sitesinde mevcuttur. website veya ürün ambalajı.
Ziyaret edebilirsiniz Amazon'daki Performans Araçları Mağazası Daha fazla ürün bilgisi ve destek kaynakları için.