Performance Tool W1614 2 Ton (4,000 lbs.) Kapasiteli Yer Tipi Kriko Kullanım Kılavuzu

giriiş

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Performance Tool W1614 2 Ton (4,000 lbs.) Capacity Floor Jack. Designed for heavy-duty lifting tasks, this floor jack is constructed from durable steel and features swivel rear casters for easy positioning. It has a maximum lifting capacity of 4,000 pounds and can reach a maximum height of 15 inches.

Figure 1: Performance Tool W1614 2 Ton Floor Jack.

Güvenlik Bilgileri

UYARI: Bu ürün, Kaliforniya Eyaleti tarafından kansere ve doğum kusurlarına veya üremeyle ilgili diğer zararlara neden olduğu bilinen kurşun dahil kimyasallara maruz kalmanıza neden olabilir. Daha fazla bilgi için www.P65Uyarılar.ca.gov.

Always read and understand all instructions and warnings before using this floor jack. Failure to follow these instructions may result in serious injury or property damage.

• Sert ve düz bir yüzeyde kullanın: Always operate the jack on a hard, level surface capable of supporting the load.
• Kriko Ayaklarını Kullanın: This floor jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Do not work under a vehicle supported only by a floor jack.
• Do Not Exceed Rated Capacity: Never exceed the 4,000 lbs. (2 Ton) rated capacity of this jack.
• Center Load on Saddle: Ensure the load is centered on the jack saddle to prevent slipping.
• Chock Wheels: Always chock the wheels that are not being lifted.
• Açık Tutun: Ellerinizi, ayaklarınızı ve diğer vücut bölgelerinizi hareketli parçalardan ve sıkışma noktalarından uzak tutun.
• Kullanmadan Önce İnceleyin: Her kullanımdan önce, kriko üzerinde herhangi bir hasar, sızıntı veya gevşek parça olup olmadığını kontrol edin. Hasarlıysa kullanmayın.
• Aşırı Yük Koruması: This jack is equipped with an overload protection bypass valve for safety. Do not attempt to bypass or modify this feature.

Kurulum ve İlk Hazırlık

Before first use, or if the jack has been stored for an extended period, it is important to bleed any air from the hydraulic system to ensure proper operation. Air in the system can cause the jack to lift unevenly or not lift at all.

Bleeding the Hydraulic System:

1. Locate the release valve. This is typically a screw or knob that controls the lowering function.
2. Kolu kol yuvasına takın.
3. Tahliye vanasını tamamen açmak için kolu saat yönünün tersine çevirin.
4. Pump the handle fully up and down approximately 10-15 times to force any trapped air out of the system.
5. Tahliye valfini kapatmak için kolu saat yönünde çevirin.
6. Test the jack by pumping the handle to raise the saddle. It should raise smoothly and evenly. If not, repeat the bleeding process.

Şekil 2: Açısal view of the floor jack, showing the handle socket and general structure.

Kullanım Talimatları

Lifting a Vehicle:

1. Aracı sert ve düz bir zemine park edin. El frenini çekin ve yere temas edecek tekerlekleri takozlarla sabitleyin.
2. Locate the vehicle's manufacturer-recommended lifting points. Refer to your vehicle's owner's manual.
3. Position the floor jack so that the saddle is directly under the lifting point. Ensure the load is centered on the saddle.
4. Close the release valve by turning the handle clockwise until it is firmly closed. Do not overtighten.
5. Aracı istenilen yüksekliğe kaldırmak için kolu yukarı ve aşağı pompalayın. Sadece kriko ayaklarını yerleştirebileceğiniz kadar yükseltin.
6. Immediately place appropriately rated jack stands under the vehicle's designated support points.
7. Slowly open the release valve by turning the handle counter-clockwise to lower the vehicle onto the jack stands. Once the vehicle is securely resting on the jack stands, remove the floor jack.

Lowering a Vehicle:

1. Ensure the area around the vehicle is clear of obstructions and personnel.
2. Position the floor jack saddle directly under the vehicle's lifting point, adjacent to the jack stands.
3. Pump the jack handle a few times to slightly raise the vehicle off the jack stands.
4. Krikoları aracın altından dikkatlice çıkarın.
5. Slowly turn the jack handle counter-clockwise to open the release valve. The vehicle will begin to lower. Control the lowering speed by adjusting how much you open the valve.
6. Once the vehicle is fully lowered, remove the floor jack.

Figure 3: Diagram showing key dimensions and lift range of the floor jack.

Bakım

• Yağlama: Tüm hareketli parçaları periyodik olarak hafif makine yağı ile yağlayın.
• Hidrolik Sıvı: Check the hydraulic fluid level regularly. If low, add high-quality hydraulic jack oil. Do not use brake fluid or other types of oil.
• Temizlik: Keep the jack clean and free of dirt, grease, and debris.
• Depolamak: Store the jack in a dry, clean place with the ram fully retracted to prevent rust and extend seal life.
• Denetleme: Regularly inspect for any signs of wear, damage, or leaks. If any issues are found, do not use the jack and have it serviced by qualified personnel.

Sorun giderme

Özellikler

Garanti ve Destek

For specific warranty information, please refer to the documentation included with your purchase or contact Performance Tool customer service. Keep your purchase receipt for warranty claims.

Resmi Kullanıcı Kılavuzu'nu (PDF) indirebilirsiniz: Kullanıcı Kılavuzunu İndirin (PDF)

For technical support or inquiries, please visit the official Performance Tool websitesine bakın veya müşteri hizmetleri departmanıyla iletişime geçin.