Performance Tool W1612 2.5 Ton Hydraulic Floor Jack User Manual

1. Güvenlik Bilgileri

Always prioritize safety when operating the Performance Tool W1612 hydraulic floor jack. Failure to follow these instructions may result in serious injury or property damage.

• Kılavuzu okuyun: Read and understand all instructions and warnings in this manual before using this product.
• Sert ve düz bir yüzeyde kullanın: Operate the jack only on a hard, level surface capable of supporting the load. Avoid uneven or soft ground.
• Kapasiteyi aşmayın: Never exceed the rated capacity of 5,000 lbs (2.5 tons).
• Kriko Ayaklarını Kullanın: After lifting the vehicle to the desired height, always support it immediately with appropriately rated jack stands. The hydraulic jack is a lifting device only and is not designed to sustain loads for extended periods.
• Yükü ortalayın: Ensure the load is centered on the jack saddle. Off-center loads can cause instability.
• Güvenlik Donanımı Giyin: Always wear ANSI-approved safety goggles and heavy-duty work gloves during operation.
• Açık Tutun: Keep hands, feet, and other body parts clear of moving parts and the vehicle during lifting and lowering.
• Kullanmadan Önce İnceleyin: Her kullanımdan önce, kriko üzerinde herhangi bir hasar, sızıntı veya gevşek parça olup olmadığını kontrol edin. Hasarlıysa kullanmayın.
• Uygun Depolama: Store the jack in a clean, dry place, fully lowered, when not in use.

2. Ürün Bittiview

The Performance Tool W1612 is a heavy-duty 2.5 ton (5,000 lb) hydraulic floor jack designed for lifting vehicles. It features a robust steel construction, wide front wheels, and a 360-degree swivel saddle for ease of use.

Temel Bileşenler:

• Kaldırma Kolu: The main arm that raises and lowers the vehicle.
• Sele: The contact point with the vehicle's lifting area.
• Halletmek: Used for pumping to lift and rotating to lower.
• Tahliye Valfi: Krikonun indirme hızını kontrol eder.
• Tekerlekler/Tekerlekli Ayaklar: Allow for easy positioning and maneuvering.

Figure 1: Performance Tool W1612 2.5 Ton Hydraulic Floor Jack. This image shows the overall design of the yellow hydraulic floor jack with its long handle and wheels.

Şekil 2: Yan view of the Performance Tool W1612 Hydraulic Floor Jack. This image provides a different angle of the jack, highlighting its low-profile design and robust construction.

3. Kurulum

İlk Hazırlık:

1. Paketin açılması: Carefully remove the jack from its packaging. Inspect for any shipping damage.
2. Kol Montajı: Insert the handle into the handle socket and secure it according to the instructions provided in the packaging.

Bleeding the Hydraulic System:

Air can become trapped in the hydraulic system during shipping or use, affecting performance. Bleeding the system removes this air.

1. Open Release Valve: Tahliye vanasını tamamen açmak için kolu saat yönünün tersine çevirin.
2. Pompa Kolu: Pump the handle 6-8 full strokes to force air out of the system.
3. Tahliye vanasını kapatın: Tahliye valfini kapatmak için kolu saat yönünde çevirin.
4. Test: Test the jack by lifting and lowering it a few times without a load. If the jack does not lift smoothly or to its full height, repeat the bleeding process.

4. Kullanım Talimatları

Lifting a Vehicle:

1. Aracı Hazırlayın: Aracı sert ve düz bir zemine park edin. El frenini çekin ve yerde kalacak tekerlekleri takozla sabitleyin.
2. Jack'in pozisyonu: Position the jack directly under the vehicle's designated lifting point. Consult your vehicle's owner's manual for proper lifting points.
3. Tahliye vanasını kapatın: Tahliye vanası sıkıca kapanana kadar kolu saat yönünde çevirin. Aşırı sıkmayın.
4. Kaldırma Aracı: Pump the handle up and down to raise the vehicle to the desired height. Ensure the vehicle remains stable during lifting.
5. Kriko ayaklarıyla sabitleyin: Once the vehicle is at the desired height, immediately place appropriately rated jack stands under the vehicle's frame or designated support points.
6. Biraz daha aşağıya, sehpalara indirin: Slowly turn the handle counter-clockwise to open the release valve, allowing the vehicle to gently rest onto the jack stands. Remove the hydraulic jack once the vehicle is securely supported by the stands.

Lowering a Vehicle:

1. Jack'i yeniden konumlandırın: If removed, place the hydraulic jack back under the vehicle's lifting point and raise it slightly to take the load off the jack stands.
2. Kriko ayaklarını çıkarın: Krikoları aracın altından dikkatlice çıkarın.
3. Aracı İndir: Slowly turn the handle counter-clockwise to open the release valve. Control the lowering speed by adjusting how much you open the valve.
4. Tamamen Aşağı: Araç tamamen indirildikten sonra krikoyu çıkarın.

5. Bakım

Düzenli bakım, hidrolik krikonuzun uzun ömürlü olmasını ve güvenli çalışmasını sağlar.

• Hidrolik Sıvı Seviyesi: Check the hydraulic fluid level periodically. With the jack fully lowered, remove the oil filler plug. The fluid level should be just below the filler hole. Top up with high-quality hydraulic jack oil if necessary. Do not use brake fluid or motor oil.
• Yağlama: Lubricate all moving parts and pivot points with light machine oil monthly or as needed.
• Temizlik: Keep the jack clean and free of dirt, grease, and corrosive materials. Wipe down the ram and pump plungers after each use.
• Depolamak: Store the jack in a dry, protected area, fully lowered, to prevent rust and seal damage.

6. Sorun Giderme

7. Özellikler

• Modeli: W1612
• Yük Kapasitesi: 5,000 lbs (2.5 Tons)
• Maksimum Kaldırma Yüksekliği: 19.25 inç
• Minimum Kaldırma Yüksekliği: Approximately 5 inches (standard floor jack minimums)
• Malzeme: Alaşımlı Çelik
• Ürün Ağırlığı: 79.7 pound
• Ürün Ölçüleri (U x G x Y): 30.6 x 8.6 x 15.4 inç
• Araç Hizmet Tipi: Araba, Kamyon

8. Garanti ve Destek

For warranty information or technical support regarding your Performance Tool W1612 hydraulic floor jack, please refer to the documentation included with your purchase or contact Performance Tool customer service directly. Keep your purchase receipt for warranty claims.

Üretici: Performance Tool (Wilmar Corporation)

UPC: 039564124778

İlk Mevcut Tarih: 1 Nisan 2004